Service Manual SIPLACE SmartFeeder.pdf - 第145页

7 Repairs to SmartFeeder 8 mm X / Xi 7.11 Wiper Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 145 7.11 Wiper Required spare part Fig.45: Wiper for foil disposal X8Smart F…

100%1 / 246
7 Repairs to SmartFeeder 8 mm X / Xi
7.10 Tamp wheel / spiral gear
144 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
► Tilt the feeder module to the right and hold the
Allen screw on the spiral gear with one finger.
► Fasten the bearing screw (03050825‑xx).
Use a flat-bladed screwdriver for this.
► Fasten the Allen screw to the spiral gear on the
left side.
Use a size 4 Allen key with 0.9Nm for this.
► Fasten the wiper (see 7.11.2 "Fitting the stripping
device 8 mm X" [}146]).
► Fasten the rocker (see 7.9.1.2 "Fitting the rocker
assembly" [}137]).
► Fit the bearing cap onto the foil stripping unit, as
shown.
► Fasten the bearing cap with the three screws
shown(1)
. Use a Phillips screwdriver with 0.9 Nm
for this.
► Fasten the left side cover (see 7.3.2 "Fitting the
left side cover" [}102]).
7 Repairs to SmartFeeder 8 mm X / Xi
7.11 Wiper
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 145
7.11 Wiper
Required spare part
Fig.45: Wiper for foil disposal X8Smart
Feeder module Item no. Designation
SmartFeeder 8mm X
SmartFeeder 8 mm Xi
03106790Sxx Wiper for foil disposal X8Smart
03071821-xx SN 213307-H-M2.5 x 3-A2-70
Tools required
●
Phillips screwdriver, small
●
Tweezers
7 Repairs to SmartFeeder 8 mm X / Xi
7.11 Wiper
146 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.11.1 Removing the stripping device 8 mm X
► Carefully place the feeder module with the left side
down on a stable, level and clean surface.
► Insert the Phillips screwdriver through the opening in
the rocker(1)
.
► Remove the Phillips screw(2), which is fastening the
stripping device.
► Press the rocker(3) backwards.
► Pull the stripping device(4) upwards.
► Lower the rocker again.
► Remove the stripping device.
7.11.2 Fitting the stripping device 8 mm X
► Press the rocker(1) backwards.
► Insert the stripping device(2) as shown, with the flat
side facing upwards.
► Align the stripping device so that it is straight.
Make sure that the hole for the screw is visible through
the hole in the stripping device and that the individual
parts of the stuffing gear protrude through the recesses
(3)
of the stripping device.
► Lower the rocker again.
► Use a pair of tweezers to hold the Phillips screw(4)
over the drilled hole.
► Insert the Phillips screwdriver through the opening in
the rocker(5)
.
► Hand-tighten the Phillips screw fastening the strip-
ping device.