Service Manual SIPLACE SmartFeeder.pdf - 第128页
7 Repairs to SmartFeeder 8 mm X / Xi 7.7 Drives 128 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 ► Turn the feeder module onto the other side. ► Fasten the bearing blocks…
7 Repairs to SmartFeeder 8 mm X / Xi
7.7 Drives
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 127
► Use tweezers to carefully push the outer bearing
block(4)
onto the motor shaft.
► Apply a little grease to the worm gear(5).
Use Klübersynth GE14-151 for this.
► Push the two bearing blocks(6) into the position
shown.
► Fasten the motor with the two Allen screws
marked(7)
. Use a size 2 angled Allen key for this
(hand-tighten).
► Apply a little grease to the bearing blocks(6).
Use Klübersynth GE14-151 for this.
► Insert the motor cable connector into the connec-
tion on the control board. (8)
► Close the connection.
7 Repairs to SmartFeeder 8 mm X / Xi
7.7 Drives
128 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
► Turn the feeder module onto the other side.
► Fasten the bearing blocks with the two Phillips
screws(9)
(hand-tight).
► If necessary, correct the position of the bearing
blocks.
► Make sure that the spiral gear only has grease on
the small toothed wheel and that the large
toothed wheel is free of grease. You may need to
remove any grease on the larger toothed wheel!
► Place the feeder module in a stable, upright posi-
tion.
► Insert the spiral gear(10) into the hole provided,
with the smaller toothed wheel at the front. Make
sure that the small toothed wheel of the spiral
gear engages properly with the worm gear of the
motor.
► Fasten the spiral gear (hand-tight) with the bear-
ing screw(11)
. Use a flat-bladed screwdriver to
help you.
► Tighten the left-hand side of the spiral gear(12)
with a size 4 Allen key(13) and 0.9 Nm.
► Fit the bearing cap(14) onto the foil stripping
unit, as shown.
► Fasten the bearing cap with the three marked
screws ISO 7046-2-M2.5x 6-A2-70-H (item no
03023228-xx)(15)
, using a Phillips screwdriver
and 0.9Nm.
► Fasten the left side cover (see 7.3.2 "Fitting the
left side cover" [}102]).
7 Repairs to SmartFeeder 8 mm X / Xi
7.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 129
7.8 Foil rocker
7.8.1 Foil rocker assembly
Spare part required
Fig.38: Foil rocker assembly
Fig.39: Cable light barrier emitter
Feeder module Item no. Designation
SmartFeeder 8mm X
SmartFeeder 8 mm Xi
03101471Sxx
03063591-xx
Foil rocker assembly /X8Smart
Cable for light barrier emitter 2x8
Tools required
●
Flat-bladed screwdriver size 1 or tweezers
●
TORX screwdriver size T8