Service Manual SIPLACE SmartFeeder.pdf - 第227页

8 Repairs to SmartFeeder 2x8 mm X / Xi 8.11 Knurled Tamp Wheel Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 227 8.11 Knurled Tamp Wheel Spare part required Fig.72: Knurl…

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.10 Rocker

226 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.10.2 Replacing the individual parts of the rocker

Spare parts required

Fig.71: Rocker, tamp wheel and bearing shaft

Feeder module Item no. Designation

SmartFeeder 2x8mmX

SmartFeeder 2x8 mm Xi

03041735-xx Rocker with holder/foil disposal X8

03041017-xx Tamp wheel /rocker X8

03042321-xx Bearing shaft for rocker /X8

Tools required

●

Flat-bladed screwdriver

●

Tweezers

8.10.2.1 Removing the tamp wheel and bearing shaft

► Place the feeder on a stable, level and clean sur-

face.

► Remove the rocker as described in 8.10.1.1 "Re-

moving the Rocker Complete" [}225].

► Screw off the bearing shaft(1) and remove the

tamp wheel.(2)

8.10.2.2 Fitting the tamp wheel and bearing shaft

► Insert the tamp wheel into the rocker.(1)

► Insert the bearing shaft through the hole in the

rocker, through the tamp wheel and then screw it

in place.(2)

► Fasten the rocker as described in section

8.10.1.2

"Fitting the rocker" [}225].

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.11 Knurled Tamp Wheel

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 227

8.11 Knurled Tamp Wheel

Spare part required

Fig.72: Knurled tamp wheel

Feeder module Item no. Designation

SmartFeeder 2x8mmX

SmartFeeder 2x8mmXi

03061111Sxx Knurled tamp wheel

03083028-xx DIN 988-3x6x0.1-1.4310 (washer)

00305726-xx DIN 471-3x0.4-C67 (circlip)

03003122-xx Compensating disk /DI3.1

Tools required

●

TORX screwdriver 0.6Nm, size T8

●

Phillips screwdriver

●

Flat-bladed screwdriver

●

Tweezers

●

Circlip pliers for outer rings 3-10 mm

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.11 Knurled Tamp Wheel

228 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.11.1 Removing the knurled tamp wheel left

► Place the feeder on a stable, level and clean sur-

face.

► Remove the left and right side covers. (See 8.3.1

"Removing the Left Side Cover" [}174], 8.3.3

"Removing the Right Side Cover" [}175])

► Remove the rocker. (See 8.9.1.1 "Removing the

Foil Rocker Cpl." [}219])

► Remove the stripping device. (See 8.12.1 "Re-

moving the wiper" [}230])

► Remove the toothed wheel 4 tape. (See Remov-

ing the Gear Wheel 4 Foil left)

► Remove the circlip.(1)

► Remove the top washer.(2)

► Remove the tamp wheel.(3)

► Remove the large washer.(4)

8.11.2 Fitting the knurled tamp wheel left

► Grease the shaft and the circlip with Polyhub Gly

801.

► Replace the large washer.(1)

► Fit the new knurled tamp wheel.(2)

► Replace the top washer.(3)

► Replace the circlip.(4)

► Refit the toothed wheel 4 tape. (See Fitting the

Gear Wheel 4 Foil left)

► Reinsert the stripping device (see 8.12.2 "Fitting

the wiper" [}230]).

► Reinsert the rocker (see 8.9.1.2 "Fitting the Foil

Rocker Cpl." [}219]).

► Fit the covers (see 8.3.2 "Fitting the Left Side

Cover" [}175], 8.3.4 "Fitting the Right Side

Cover" [}176]).