Service Manual SIPLACE SmartFeeder.pdf - 第97页

7 Repairs to SmartFeeder 8 mm X / Xi  Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 97 7 Repairs to SmartFeeder 8 mm X / Xi Feeder module Item no. Description SmartFeeder…

6 Repairs to SmartFeeder 4 mm X / Xi

6.17 Foil container

96 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

7 Repairs to SmartFeeder 8 mm X / Xi



Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 97

7 Repairs to SmartFeeder 8 mm X / Xi

Feeder module Item no. Description

SmartFeeder 8mmX 00141370-xx

00141390-xx

SIPLACE SmartFeeder 8mm X

SIPLACE SmartFeeder 8mm X splice sensor

SmartFeeder 8 mm Xi 00141480-xx

00141500-xx

SIPLACE SmartFeeder 8mm Xi

SIPLACE SmartFeeder 8mm Xi splice sensor

Notes about SmartFeeder Xi

The SmartFeederXi feeder modules support high infeed speeds for maximum utilization of the

machine placement capacity with the SIPLACE SpeedStar CP20P2 placement head.

The corrugated slide on the back of the SmartFeeder is a clear identifying feature of the Smart-

Feeder Xi.

SIPLACE Pro shows the SmartFeederXi as a SmartFeederX. If a CP20P2 head is used in the

setup, SIPLACE Pro automatically assumes that a SmartFeederXi is being used. The maximum

speed of a SmartFeederXi depends on the placement head which uses this feeder module.

The station software also shows a SmartFeederXi as a SmartFeederX. If a faster SmartFeederXi

is needed for performance purposes (machine with CP20P2 head), although a slower Smart-

FeederX is configured, the feeder LED will flash briefly, to signal the status "Not fast enough". The

station software will mark this feeder orange with the status "Too slow".

The SmartFeeder 8mmXi feeder module can be operated at any machine which can already ac-

commodate the SmartFeeder 8mmX. Due to the shift of the pickup position, there is an incompat-

ibility with older software versions. For this reason, the following station software versions are re-

quired:

●

≥ SIRIO 707.1SP2.HF9

●

≥ 605.03 SP5 + HF9

For more information about introducing the SmartFeederXi, refer to the technical information "In-

troducing the SmartFeeder modules Xi" (German [TI2018-09D14], English [TI201809E14]).

7 Repairs to SmartFeeder 8 mm X / Xi

7.1 Front sliding guide/sliding foil

98 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

7.1 Front sliding guide/sliding foil

Required spare part

Fig.28: Sliding foil

Feeder module Item no. Designation

SmartFeeder 8mmX

SmartFeeder 8mmXi

03019604Sxx Sliding foil, X-feeder JUM-S-06LY

Tools required

●

Sliding foil remover

7.1.1 Removing the Sliding Foil

► Place the feeder module carefully down on its

side, onto a stable, level and clean surface.

► Place the sliding foil remover into the sliding

guide, as shown in the diagram.

► Lever the sliding foil out of the engaged position.

► Pull the sliding foil out of the sliding guide, to-

wards the front.

7.1.2 Fitting the Sliding Foil

► Press the sliding foil slightly together.

► Push the sliding foil into the sliding guide, from

the front, as far as the end stop.

► Turn the sliding foil, until the slit can be fully seen

and the sliding foil engages audibly.