Service Manual SIPLACE SmartFeeder.pdf - 第54页

6 Repairs to SmartFeeder 4 mm X / Xi 6.8 Foil rocker 54 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 6.8.1.2 Fitting the Foil Rocker Assembly ► Turn the foil rocker into …

100%1 / 246
6 Repairs to SmartFeeder 4 mm X / Xi
6.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 53
6.8.1.1 Removing the Foil Rocker Assembly
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Remove the two screws(1) which fasten the foil
rocker.
Use a size T8 TORX screwdriver for this.
► Pull the foil rocker up and off(2).
► Make sure that the flat ribbon cable(3) is not
stretched too much.
► Turn the foil rocker into the position shown in the
diagram.
► Swing the holder on the flat ribbon connection
up(4).
► Pull the flat ribbon cable(5) out of the flat ribbon
cable connection.
6 Repairs to SmartFeeder 4 mm X / Xi
6.8 Foil rocker
54 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
6.8.1.2 Fitting the Foil Rocker Assembly
► Turn the foil rocker into the position shown in the
diagram.
► If this is not open, swing the bracket on the flat
ribbon connection(2)
upwards.
► Push the flat ribbon cable(1), with the blue side
pointing upwards, into the flat ribbon cable con-
nection(2)
, as far as the stop.
► Make sure that the flat ribbon cable contacts lie
against the contacts on the connection.
► Swing the bracket on the flat ribbon connection
down(2)
.
► Carefully place the foil rocker unit(3) onto the
marked fixture holes.
Make sure that the cable(4) slides into the duct well
during insertion and is not bent. If there are any prob-
lems with this, open the left side cover of the feeder
module.
► Very carefully fasten the foil rocker unit with the
two marked TORX screws hand-tight. Use a size
8 TORX screwdriver for this.
6 Repairs to SmartFeeder 4 mm X / Xi
6.8 Foil rocker
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 55
6.8.2 Replacing individual foil rocker parts
Fig.12: Individual foil rocker parts
Feeder module Position Item no. Designation
SmartFeeder 4mm X
SmartFeeder 4 mm Xi
1 03100349-xx Rocker bearing X8 Smart
2 03103850-xx Axis foil rocker X8 Smart
3 03146596-xx Foil rocker X4 Smart
4 03155518-xx Roller foil disposal X4 Smart
5 03155857-xx Pressure spring 0.45x4.05x31.01 EN
10270-1 DH
6 03033796-xx RF-SN75-2.5 x 6-9.8
7 03100381-xx Light barrier transmitter flat assy. X8Smart
Tools required
●
Flat-bladed screwdriver size 0
●
Tweezers or flat pliers
6.8.2.1 Replacing the foil rocker, axis and pressure spring
Removing individual parts
► Insert a small flat-bladed screwdriver size 0 into
the small slits on the left and right and press
slightly outwards, to open the long retaining
plates in the rocker bearings and to release the
axis from its holder(1)
.
► Pull the rocker up and out of the rocker bear-
ings.(2)