00197001-04_UM_Smart_Pin_Support_X-Series-S_SX12V2_DE_EN.pdf - 第111页
6 Restrictions User Manual / Bedienungsanleitung SIPLACE X-Series S, SX1/SX2 V2 Smart Pin Support Operation and Configura- tion 05/2019 111 6 Restrictions ● SIPLACE Pro does not check if the support pin positions are v…
5 Sample Applications
5.3 Smart Pin Support and PCB Barcode Mode
110 User Manual / Bedienungsanleitung SIPLACE X-Series S, SX1/SX2 V2 Smart Pin Support Operation and Configura-
tion 05/2019
5.3 Smart Pin Support and PCB Barcode Mode
In the following, a sample workflow at the station is displayed, when Smart Pin Support is used in
combination with PCB Barcode mode in asynchronous conveyor mode.
Prerequisites:
●
The jobs in PCB barcode mode are prepared in SIPLACE Pro as follows:
– Job 1: PCB1 with Barcode A -> Support pin list 1
– Job 2: PCB2 with Barcode B -> Support pin list 2
– Job 3: PCB3 with Barcode C -> Support pin list 3
●
Support pin positions are only changed if another pin position is loaded with a changed place-
ment program.
●
The station runs in asynchronous dual conveyor lane mode.
Workflow at the Station
●
Job 1 with PCB1 for Conveyor 1 is defined, the support pins from the Support pin list 1 are ad-
justed on the lifting table.
●
Job 1 with PCB1 for Conveyor 2 is defined, the support pins from the Support pin list 1 are ad-
justed on the lifting table.
●
PCB1 is moved into Conveyor 1: the PCB is moved to the processing area and gets placed.
●
PCB2 is moved into Conveyor 1: the PCB is moved into the input section.
●
While PCB1 in Conveyor 1 is still being placed, a PCB3 is moved into Conveyor 2: the PCB is
moved into the input section. The conveyor interface is disabled for both conveyor lanes.
●
When the placement of PCB1 in Conveyor 1 is completed, it is moved on and no PCB is
moved into the processing area.
●
The support pins from Support pin list 3 are completely adjusted on Conveyor 2:
The support pins on Conveyor 1 are adjusted from Support pin list 1 to Support pin list 2.
●
The boards in the input sections (Conveyor 1 and 2) are transported to the processing area
and get placed. The conveyor interface is enabled for both lanes again.
●
While PCB2 is still being placed in Conveyor 1, a PCB1 is moved in. PCB1 is moved into the
input section. As soon as PCB2 has been completely placed in the processing area, the sup-
port pins on Conveyor 1 will be adjusted from Support pin list 2 to Support pin list 1.
●
After the adjustment, PCB1 is transported from the input section to the processing area and
gets placed.
●
While PCB3 is still being placed in Conveyor 2, a PCB3 is moved in. PCB3 is moved into the
input section. As soon as PCB3 has been completely placed in the processing area, PCB3 is
moved from the input section into the processing area and gets placed.
6 Restrictions
User Manual / Bedienungsanleitung SIPLACE X-Series S, SX1/SX2 V2 Smart Pin Support Operation and Configura-
tion 05/2019
111
6 Restrictions
●
SIPLACE Pro does not check if the support pin positions are valid at the station.
●
The combination of Smart Pin Support with LBO and PCB Barcode mode is only possible if
the support pin positions do not change.
●
In PCB Barcode mode combined with Smart Pin Support, the support pin positions can be
changed. However, in this case the productivity will be reduced, because the placement
machine must run empty before. If the same support pin list is used for the different boards,
the support pins will not be moved.
●
Virtual PCB Stack is not supported.
For more machine-specific restrictions, read the applicable assembly instructions
●
Assembly instruction "Smart Pin Support option for SIPLACE SX1/SX2 V2" [DE+EN:
00197002‑xx]
●
Assembly instructions "Smart Pin Support option for SIPLACE X-Series S" [DE+EN:
00197394‑xx]
6 Restrictions
112 User Manual / Bedienungsanleitung SIPLACE X-Series S, SX1/SX2 V2 Smart Pin Support Operation and Configura-
tion 05/2019