00193922-03.pdf - 第230页

5 Tasks on the machine User manual SIPLACE HF series 5.3 Carrying out a walk-through inspection Software Version SR.50x.xx 01/2006 US Edition 230 5.3.2 Spl icing the t ape in good time PLEA SE NOT E: S pli ce the tapes e…

User manual SIPLACE HF series 5 Tasks on the machine

Software Version SR.50x.xx 01/2006 US Edition 5.3 Carrying out a walk-through inspection

229

5.3 Carrying out a walk-through inspection

5.3.1 Checking the S feeder modules

Æ Make sure that the tape is correctly placed in the springs of the S feeder module.

Fig. 5.3 - 1 Placing the tape in the springs of the S feeder module

Æ Check to see whether the tape foil removal container for the S feeder module is full.

If it is full, then pull out the foil and cut it off with scissors.

PLEASE NOTE

Tearing the foil instead of cutting it can lead to problems with the tape removal mechanism.

For this reason the 3 x 8 mm feeder modules are fitted with an integral cutter. This is in the

tape foil removal container at the end of the feeder module under the flaps. 5

Æ Check to ensure that the pick-up window on the feeder module is the right size for the com-

ponent.

Æ Check to see whether tape guides are inserted on combination feeder modules (24 mm /

32 mm).

Æ Check to see whether the additional plastic guide is inserted on combination feeder modules.

5 Tasks on the machine User manual SIPLACE HF series

5.3 Carrying out a walk-through inspection Software Version SR.50x.xx 01/2006 US Edition

230

5.3.2 Splicing the tape in good time

PLEASE NOTE:

Splice the tapes early enough so that the feeder modules do not run out of components. Oth-

erwise you will experience prolonged down times.

However, do not splice the tapes too early because if you wind the end of the old tape onto

the new reel after splicing, the reel holding the new tape may become overfilled and the tape

will slip off the reel and become tangled up. This will again result in pick-up errors and pro-

longed down times. 5

5.3.3 Checking the PCB supports

Check the position of the magnetic PCB supports on the lifting table:

– Make sure that the PCB supports do not collide with components on the underside of the

PCBs.

– In addition, make sure that the PCB supports do not collide with the PCB conveyor pan-

els.

5.3.4 Inserting separating plates in the tape container

Æ The separating plate has different edges and can be inserted into the tape container in two

ways. If spindles are used, the recesses for the spindles in the separating plate point upwards

(see item 6 in Fig. 5.3 - 2

). If you do not use spindles, the rounded edge of the separating plate

points up (see item 5 in Fig. 5.3 - 2

Æ Insert the separating plates as shown in Fig. 5.3 - 2 and remember that the smallest division

of the tape container is a 2x division. This will help avoid placement errors.

Æ Check that the separating plates engage in the same positions on the three guide rails. Oth-

erwise the separating plate will be offset or bent.

User manual SIPLACE HF series 5 Tasks on the machine

Software Version SR.50x.xx 01/2006 US Edition 5.3 Carrying out a walk-through inspection

231

Fig. 5.3 - 2 Separating plates in the tape container

(1) Guide rail for the separating plates

(2) Tape container

(3) Waste tape container

(4) Sliding surfaces for the tape reels

(5) Position of the separating plate if no spindles are used

(6) Position of the separating plate if spindles are used