2OM-1011-002.pdf - 第128页
0305-001 Tg0858-PM-PM 4.5 COMPONENT DA T A Display (2) When the [DA T A EDIT] key is pressed, the data edit display appears on the screen. • When the [TRA Y STEP INFO] key *1 is pressed at the “COMPONENT DA T A-TRA Y-” d…
0305-001 Tg0858-PM-PM
4.5 COMPONENT DATA Display
(1) When the [TAPE [A] (F101-F139)], the [VIB STICK [A] (F141-F199)],
or the [TRAY L (F301-F599)] key is pressed at the “PATTERN PRO-
GRAM EDIT” display, the corresponding display (Fig. 2B158, 2B159, or
2B160) appears on the screen.
When the [TAPE [B] (F201-F239)], the [VIB STICK B (F241-F299)], or
the [TRAY R (F601-F899)] key is pressed at the “PATTERN PROGRAM
EDIT” display, the corresponding display (similar to Fig. 2B158, 2B159, or
2B160) appears on the screen.
Fig. 2B158
[TAPE A]
[VIB. STICK A]
[TRAY L]
*1
Fig. 2B159
Fig. 2B160
Fig. 2B156
Fig. 2B157
For Tape Feeder
4.5 COMPONENT DATA Display
2-108
0305-001 Tg0858-PM-PM
4.5 COMPONENT DATA Display
(2) When the [DATA EDIT] key is pressed, the data edit display appears on
the screen.
• When the [TRAY STEP INFO] key *1 is pressed at the “COMPONENT
DATA-TRAY-” display, the “TRAY (L) STEPS INFORMATION” display
appears on the screen.
Refer to “4.5.3 Editing of Tray (L or R) Steps Information Data of Section
2” for details.
4.5.1 Editing of Component Data for Tape and Stick Feeders
The following example is based on the component data for Tape Feeder A.
As for Tape Feeder B and Vibratory Stick Feeders A and B, similar data edit
displays appear on the screen.
Operation Procedure
(1) When the [DATA EDIT] key is pressed at the “COMPONENT DATA”
display (Fig. 2B158), the following display appears on the screen.
Fig. 2B161
(2) Move the line cursor to the feeder No. (FDR NO) of the data to be edited.
(3) Press the [COMPONENT ID] key to enable the selection of component
IDs.
(4) Select a component ID with the [ ] or the [ ] key beside the “COMPO-
NENT ID LIST (XXX/800)” list box.
(5) Press the [SET] key. The selected component ID is set.
2-109
0305-001 Tg0858-PM-PM
4.5 COMPONENT DATA Display
(6) Edit the component data as follows.
• When the [C] key is selected, a control command can be entered. Press-
ing the [COMMENT] key also makes it possible to enter a comment.
• When the [COMPONENT ID INITIALIZED] key is pressed, the key
turns red. Pressing the [SET] key subsequently clears the component
ID which corresponds to the selected feeder No. (FDR NO).
Ref.: When the [COMPONENT ID INITIALIZED] key in red is
pressed again, the component ID initialization mode is can-
celled.
• When the [VIB. STICK UNIT] key is pressed, the lane (FDR NO) is
set to the slot No. of the feeder on the vibratory stick feeder unit.
Refer to “2.5.1 Tape Feeders of Section 2” for the setting of the vibra-
tory stick feeder unit.
• When the [AUTO] key beside the label “CMPNT ID LIST CURSOR”
is pressed, the line cursor in the list box automatically moves to the
component ID for the selected feeder slot No. (FDR NO).
When the [LOCK] key is pressed, the line cursor in the list box is
locked (fixed). However, it can be moved only with the [ ] or the [ ]
key beside the list box.
• Press the [STEP INSERT] or the [STEP DELETE] key to insert or
delete the data line (step) of the feeder slot No. where the line cursor is
located.
• When the [PROGRAM CHECK] key is pressed, the edited pattern
program is checked.
(7) When the [RTN] key is pressed, the “COMPONENT DATA” display for
“TAPE A” appears on the screen.
2-110