80S-20用户手册.pdf - 第427页

SIPLACE 80S -20/F4 User Manual 10 Component handling Software version SR.407.xx 01/2001 US Edition 10.2 Technical data for the feeder modules 427 10.2 T echnica l dat a for the feeder modules The foll owing pages c ontai…

100%1 / 570
10 Component handling SIPLACE 80S-20/F4 User Manual
10.1 Overview Software version SR.407.xx 01/2001 US Edition
426
10.1.1 Safety instructions for processing capacitors based on powdered metal
There is a risk associated with processing capacitors based on powdered metal (e.g. tantalum). 10
The risk is that 10
– An exothermic reaction, i.e. a sudden build-up of heat, may occur if these components are
damaged. If the ambient conditions are unfavorable, and depending on the capacitance, this
build-up of heat can cause damage.
– This effect can occur when these components are cut.
Please contact your suppliers to clarify whether the components that you handle are affected. 10
In extremely rare cases, this risk can occur in the tape cutter of SIPLACE machines, with the re-
mote possibility of causing a smoldering fire in the waste tape. 10
The ambient conditions are unfavorable if: 10
(1) The components remain on the tape while the set tape cycle is checked (since the operator
can cycle the feeder onward without removing components during this check).
(2) The components remain on the tape, e.g. due to a tear in the cover foil.
(3) The components remain on the tape, and the components or tape do not conform to the
specification, thus increasing the pick-up error rate.
Please follow the instructions given below to minimize the risk when placing capacitors based on
powdered metal. 10
(1) If the component tape is cycled onward manually, the operator must remove any components
remaining in the tape pocket.
(2) If the cover foil tears, the operator must remove any components remaining on the tape.
(3) The waste tape container must be emptied regularly (recommended interval: every hour).
10
CAUTION
To avoid the risk, it is essential to use only feeders that have
been approved for placing such components, namely:
Article no.: 00141117-01 Model E
Article no.: 00141118-01 Model C/D 10
10
The feeders are labeled as shown
below:
10
Approved for
capacitors based on
metal-powder
Freigegeben für
Kondensatoren auf
Metallpulver-Basis
SIPLACE 80S-20/F4 User Manual 10 Component handling
Software version SR.407.xx 01/2001 US Edition 10.2 Technical data for the feeder modules
427
10.2 Technical data for the feeder modules
The following pages contain diagrams of all the feeder modules, technical data and the module
setting options on the placement system. 10
10.2.1 8 mm S II module
10
Fig. 10.2 - 1 8 mm S II module
Item no. 00141096-xx
Width 30 mm
Tracks per module 2
Maximum number of modules 2 x 20
Magazine capacity for 7" reels Approx. 10000
Reel diameter 7" - 15" (up to 381 mm)
Feeding stroke (variable) 2mm / 4mm
Cycle time 60 ms
Main power supply 30 VDC
10 Component handling SIPLACE 80S-20/F4 User Manual
10.2 Technical data for the feeder modules Software version SR.407.xx 01/2001 US Edition
428
10.2.2 3 x 8 mm S module
10
Fig. 10.2 - 2 3 x 8 mm S module
Item no. 00141098-xx
Width 30 mm
Tracks per module 3
Maximum number of modules 2 x 20
Magazine capacity for 7" reels Approx. 10,000
Reel diameter 7" - 15" (up to 381 mm)
Feeding stroke (variable) 2mm / 4mm
Cycle time 60 ms
Main power supply 30 VDC
LIMITED COMPONENT PICK-UP OPTIONS:
If the following combination of track, location and conveyor track is used, components cannot be
picked up from triple conveyors.
Location/Track Conveyor track
1/115 3
3/1 1 10