80S-20用户手册.pdf - 第451页
SIPLACE 80S -20/F4 User Manual 10 Component handling Software version SR.407.xx 01/2001 US Edition 10.7 Wafflepack Changer (80F4) 451 10.7 W afflep ack Changer (80F 4 ) 10.7.1 Overview 10 Fig. 10.7 - 1 Wafflepack changer…
10 Component handling SIPLACE 80S-20/F4 User Manual
10.6 Component table, mobile Software version SR.407.xx 01/2001 US Edition
450
10.6.3 Docking the component table
WARNING 10
Check that the placement head is outside the range of the component table. 10
CAUTION 10
When docking the component table, ensure that the table bed is in its top end position and the
bracket (item 7) is folded up. 10
Å Cut off the empty tapes for the feeder modules.
Å Make sure that the contact surface (item 10) for the component table bed is clean.
Å CAREFULLY push the component table into the placement system.
Å Connect the compressed air supply (item 3).
Å Plug in the control cable (item 1).
Å Plug in the power cable (item 2) for the component table.
Å Pull the two actuating tubes (item 6) towards you at the same time and then lower the bracket
(item 7) in order to be able to lower the component table bed.
Å Check that the centring holes in the component table bed lie precisely over the centering pins
of the placement system.
Å Hold down the button (item 5) until the component table bed reaches its top end position.
Å Release the button and the component table bed will descend.
Å Ensure that the centring pins engage in the centring holes in the component table bed and that
the component table bed is fully lowered.
Å Fold up the bracket (item 7) of the component table.
Å Lock the two horizontal tensioners (item 11).
Å Close the side screens and protective cover.
Å Press the Start button to start the placement system.
10
SIPLACE 80S-20/F4 User Manual 10 Component handling
Software version SR.407.xx 01/2001 US Edition 10.7 Wafflepack Changer (80F4)
451
10.7 Wafflepack Changer (80F
4
)
10.7.1 Overview
10
Fig. 10.7 - 1 Wafflepack changer on SIPLACE F
10
(1) Wafflepack changer on location 1
(2) Pick&Place head
(3) Collect&Place head
10
10
10 Component handling SIPLACE 80S-20/F4 User Manual
10.7 Wafflepack Changer (80F4) Software version SR.407.xx 01/2001 US Edition
452
10.7.2 General Information
The use of flatpack ICs is gaining more and more importance in the manufacture of printed circuit
boards. These components have now reached the point where they are almost always delivered
on trays (wafflepack magazines). 10
The space taken up by magazine trays is however relatively high when compared with the com-
ponent density. In addition, due to their low holding capacity, the wafflepack magazines must fre-
quently be changed and if this has to be done by hand this necessarily involves interrupting the
placement process. 10
But when a wafflepack changer is used there is no time lost unnecessarily in the storing and au-
tomatic changing of the wafflepack magazines. Programmed access to up to 28 freely selectable
wafflepack magazines also increases the range of available components. 10
NOTE
The wafflepack changer is located on the lefthand side of the SIPLACE F table.
The wafflepack changer does not require the entire width of the component table. On this side of
the table 10 locations remain free which can be used for the 20 x 8 mm tape module, for example.10