Process Lens PL Service Manual_EN.pdf - 第14页
1 Introduction 14 Se rv ic e Ma nu al P ro ce ss L en s PL - 0 3/ 20 25 1.3.6 Release history Release Changes 12/2016 First edition 09/2018 New conveyor 12/2021 Integration of the service manual ASM ProcessLens Single-la…
1 Introduction
Service Manual Process Lens PL - 03/2025 13
1.3.4.3 Handling ESD modules
As a general rule: Only touch electronic modules if you must carry out work on the modules. In that
case, make sure that you do not touch the pins or printed conductors when you pick up flat modules.
Only touch components if you are earthed by one of the following measures:
●
You are wearing an ESD wristband.
●
You are wearing ESD shoes.
●
You are wearing ESD shoe earthing strips on an ESD floor.
Immediately before you touch an electronic module, discharge your own body by touching a conduct-
ive and earthed object (such as unpainted parts of a switch cabinet, a water pipe, etc.).
Do not allow modules with chargeable and highly insulating materials to touch one another, e.g. plastic
films, insulating table surfaces or items of clothing made from synthetic fibers.
Always place the modules on a conductive surface (table with an ESD coating, conductive ESD foam,
ESD bag or container).
Do not bring modules near visual display units, monitors or televisions. Keep a minimum distance of
10 cm to monitors.
1.3.4.4 Measurements and modifications to ESD modules
Only perform measurements on modules if one of the following conditions is fulfilled:
●
You are using an earthed measuring device (e.g. via PE conductors)
●
You are using a potential-free measuring device and discharge the measuring head before the
measurement (e.g.by touching an unpainted metal part of the controller casing).
► Always use an earthed soldering iron if you carry out any soldering work.
1.3.4.5 Dispatching ESD modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags or
metal sleeves) and dispatch them in conductive packaging.
► If the packaging is not conductive, place the modules in a conductive envelope before packaging.
Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for example.
NEVER use plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or short
circuit the battery terminals and, if necessary, first cover the terminals with insulating tape or
material.
1.3.5 Validity of document
This document contains service work instructions for the Process Lens PL machine.
The manual focuses on describing mechanical service work.
Please refer to the circuit diagram folder for any electrical checks.
1 Introduction
14 Service Manual Process Lens PL - 03/2025
1.3.6 Release history
Release Changes
12/2016 First edition
09/2018 New conveyor
12/2021 Integration of the service manual ASM ProcessLens Single-lane (Edition
03/2020):
●
Machine overview added for Single-lane in chapter “General”
●
Chapter “Replacing spare parts at the conveyor” divided into the sec-
tions “Dual-lane” and “Single-lane”
●
Chapter “Single-lane Machine – Calibrations” added
06/2022 Update to ProcessLens 3.0
“Vision Module HD” added to chapter “Replacing spare parts”
Renaming “ASM ProcessLens” to “Process Lens PL”.
03/2025
●
Projector replacement is described as it is now a spare part
●
Description of Lighting Calibration added
●
Gantry Parallelism Calibration updated
●
Machine descriptions Process Lens PL HD: Camera resolutions now
also with 10 μm/pixel.
●
Minor changes
1.3.7 ASMPT SMT Solutions on the World Wide Web
Simply log onto our home page at smt.asmpt.com.
The different sections contain information about our products, services and contact persons.
In addition, registered users have access to a wide range of information and applications. You can
view additional information about our products and services and access a variety of ASMPT online
tools, such as:
●
Product documentation in the ASMPT Toolkit
●
Training modules in the ASMPT Academy
●
Spare parts catalogs in the ASMPT Webshop
Registration is easy:
► Simply click on MyASMPT and then on Registration.
► Fill in the registration form and submit it.
Soon afterwards, you will receive your access authorization with user name and password.
1.4 Staff Qualifications and Training
Qualified or adequately trained personnel means that these people are familiar with the setting up,
operation and maintenance of automatic solder paste inspection systems and add-on devices and are
suitably qualified, e.g.:
●
Have been trained, instructed or authorized to switch on and off, isolate, earth and identify elec-
trical circuits and system components in accordance with normal safety standards.
●
Have been trained or instructed in the upkeep and use of appropriate safety equipment in accor-
dance with normal safety standards.
●
Have received first aid training.
1 Introduction
Service Manual Process Lens PL - 03/2025 15
1.5 Abbreviations
DLP Digital Light Processor
EMC Electromagnetic compatibility
ESD Electrostatic sensitive device
PA Placement area
PCB Board
SC Single conveyor