DECAN_S2_Admin(Eng_Ver4.5).pdf - 第176页
7-11 Part Registration SME8_ AL: Supplies parts to the motor driven 8 mm SM tap e feeder .( T ape Feeder , Auto Loading) Slim1(Stic k): Supply by Slim1 Stick Feeder . Slim2(Stic k): Supply by Slim2 Stick Feeder . Stick F…
7-10
Advanced Chip Shooter DECAN S2 Administrator’s Guide
Figure7.4 “Create a new part/Edit the selected part- Common Data” dialog box
<Feeder & Nozzle> group
<Feeder> combo box
Select the feeder type to supply components. Applicable feeder types are as
follows.
SM8L: Supply by 8mm SM Tape Feeder (Large).
SM8: Supply by 8mm SM Tape Feeder.
SM12: Supply by 12mm SM Tape Feeder.
SM16: Supply by 16mm SM Tape Feeder.
SM24: Supply by 24mm SM Tape Feeder.
SM32: Supply by 32mm SM Tape Feeder.
SM44: Supply by 44mm SM Tape Feeder.
SM56: Supply by 56mm SM Tape Feeder.
SM72: Supply by 72mm SM Tape Feeder.
SME8: Supplies parts to the motor driven 8 mm SM tape feeder.
SME12: Supplies parts to the motor driven 12 mm SM tape feeder.
SME16: Supplies parts to the motor driven 16 mm SM tape feeder.
SME24: Supplies parts to the motor driven 24 mm SM tape feeder.
SME32: Supplies parts to the motor driven 32 mm SM tape feeder.
SME44: Supplies parts to the motor driven 44 mm SM tape feeder.
SME56: Supplies parts to the motor driven 56 mm SM tape feeder.
SME72: Supplies parts to the motor driven 72 mm SM tape feeder.
7-11
Part Registration
SME8_AL: Supplies parts to the motor driven 8 mm SM tape feeder.(Tape
Feeder, Auto Loading)
Slim1(Stick): Supply by Slim1 Stick Feeder.
Slim2(Stick): Supply by Slim2 Stick Feeder.
Stick Feeder: Supply by Stick Feeder.
Tray Feeder: Supply by Tray Feeder.
<Nozzle1> combo box
Displays the nozzle that pick up the component. The types of nozzles are as
follows;
(ML150, SPLarge1, SPLarge2, SPLarge3, CN020, CN030, CN040, CN040R,
CN065, CN070R, CN110, CN140, CN220, CN400, CN400N, CN750,
CNT0B, CNT20B, LightFixB, LightFlyB, ML150, MS150, SPSmall1,
SPSmall2, SPSmall3, SpLarge1, SpLarge2, SpLarge3, ULarge1, ULarge2,
ULarge3, UMedium1, Umedium2, Umedium3)
<Pitch> combo box
Corresponds to the motor driven tape feeder. Selects the pitch of the tape
feeder selected from the <Feeder> combo box.
<Splicing Skip> combo box
If the Splicing Check sensor detects a spliced section, parts are skipped based
on the number of parts set here.
<Feeding Speed> combo box
Set the part feeding speed. For the part whose feeding speed needs to be
adjusted, select ‘Slow’ or ‘Slowest’. Inappropriate feeding speed may cause
pickup error.
Normal: Feeds parts at normal speed.
Slow: Feeds parts at a speed slightly lower than normal.
Slowest: Feeds parts at the slowest possible speed.
<Y Offset> Edit Box
When supplying parts by setting the feeding pitch of an SME 8mm or SME
8mm large electrically driven feeder to 4mm, if the Y size of the part is larger
than 2.2mm, part pickup may interfere with the tape guide.
In such case, input the Y offset value in the <Y Offset> edit box to set the part
pickup position. (Input range: 0 ~ 0.5mm)
7-12
Advanced Chip Shooter DECAN S2 Administrator’s Guide
<Sync Pick Up Tol[%]> group
As an allowable error for simultaneous pickup, it is indicated in percent based on
the part size.
The default value is 15%. If the set value is greater than this, a pickup error may
be caused even though simultaneous pickup is performed well.
In the case of micro parts, this value must be small, and pocket teaching must be
performed for parts smaller than 1005 part to reduce the part dump rate
Memo Conditions for Simultaneous Pickup
1. The part must be picked up within the allowable error range of
the center of the head that picks the part.
2. In the case of the interlocked heads, the R value must be identical
when picking up the part.
3. The maximum allowable error of the X and Y must be less than
0.5mm.
Here, the allowable error means the offset from the align point of the part to the
head center, which is the actual pickup point.
1: Head Center (Actual Pickup Point)
2: Part Align Point
<X> edit box
Set the allowance in X direction as a percentage of Part Size X at the time of