OM-1012-001.pdf - 第103页
5.2 Program Change Tg0869-PM-OM Left Side Right Side Step No. Bolt Partition Plate 5.2.2.4 Partition Plate Removal Procedure in Even Steps • When a component of 1 1.5 mm or more in height is placed on the tray t1or t2, t…
5.2 Program Change
Tg0869-PM-OM
0305-001 Chapter 1 2-23
(5) Confirm that the magazine door is latched. (Fig. A45)
If the magazine door is closed roughly, components might be bumped
out of the tray. Close it gently and securely.
If the magazine door is not latched securely, it may open suddenly dur-
ing operation (while the machine is running), causing some damage to
the machine.
5.2.2.3 Pallet Detachment from Magazine
(1) Push both handles of the magazine door fixture down in direction shown
by an arrow A to unlatch the magazine door. (Fig. A37 and Fig. A38,
Arrow A)
(2) Open the magazine door.
(Fig. A39 Arrow B)
(3) Pull out the pallet to be detached.
Fig. A44 Unlatched Magazine Door Fixture Fig. A45 Latched Magazine Door Fixture
CAUTION
5.2 Program Change
Tg0869-PM-OM
Left Side
Right Side
Step No.
Bolt
Partition Plate
5.2.2.4 Partition Plate Removal Procedure in Even Steps
• When a component of 11.5 mm or more in height is placed on the tray t1or
t2, the partition plate (even steps) should be detached to avoid interference
of the partition plate with the component.
(1) Pull the grip of the magazine door fixture down in the direction of
Arrow A to unlatch the magazine door.
(Figs. A37 and A38 Arrow A)
(2) Open the magazine door. (Fig. A39 Arrow B)
(3) Remove the bolts fixing the partition plate and remove the plate.
(a) When the partition plate is removed, confirm
the step No. and remove the partition plate only at
the even steps. If the partition plate at the odd
stage is removed and the pallet is set there, the
pallet can’t be drawn out from the magazine during
peration.
(b) The partition plate and bolts, which have been
removed will be used when the partition plate is
installed again. Set aside with care. Also, handle
the partition plate carefully because it is easily
deformed.
Fig. A46
Fig. A47 Partition Plate Anchor Bolt Position
SS
S
t
Component
S
t
1
t
2
0305-001 Chapter 1 2-24
5.2 Program Change
Tg0869-PM-OM
5.2.2.5 Partition Plate Installation Procedure in Even Steps
(1) Pull the grip of the magazine door fixture down in the direction of Arrow
A to unlatch the magazine door. (Figs. A37 and A38 Arrow A)
(2) Open the magazine door. (Fig. A39 Arrow B)
(3) Place the partition plate on the fixing block (refer to Fig. A49) and insert
it in the magazine so that the projections of the partition plate come out
from the openings at the rear wall of the magazine. (Refer to Figs. A50
and A51).
When the partition plate is being set in the magazine, note the
direction of the partition plate. Handle the magazine door and
partition plate carefully because they are easily deformed. If
the magazine door or partition plate is deformed, an error or
machine breakdown might be caused.
Fig. A50
Fig. A51
0305-001 Chapter 1 2-25
Fig. A49 Fixing Block (On the Left) Positions
(Same for on the Right)
Step No.
Fixed block with the partition plate removed
Bolt
Fig. A48 Partition Plate
Protrusions
Opening where the partition
plate protrusions are inserted
Condition showing protrusions
coming out from the openings