CP-842E-842ME System Reference-SYS-CP842-10E.pdf - 第209页
System Installation and Upgrade >> System Installation SYS-CP842-1.0E 7-3 [Advanced] Screen Specify the [Advanced] screen settings as shown below . I/O Device Configuration PCI Configuration Installed O/S: Othe…
System Installation
and Upgrade >> System Installation
7-2
SYS-CP842-1.0E
[Main] Screen
Set the [Main] screen items as shown below.
System Time and System Date
Select this item and input the current time and date using the [TAB] key to move
between items. Time is input from the left in 24 hour mode. The date order is month,
day, year.
Legacy Diskette A: Disabled*
Primary Master 6007 MB (Hard disk size)
Primary Slave None
Secondary Master CD-ROM
Secondary Slave None
Cache Memory Leave as default.
Boot Options
UBE Shadow Control
To specify the [Primary Master], [Primary Slave], [Secondary Master], and [Secondary
Slave] settings, go to the sub-menu by selecting the desired item and pressing [Enter].
If the power switches on when the initial Type setting item is set to Auto, the hard
disk will be recognized, and the correct settings will be specified automatically.
* : When the machine is equipped with the optional floppy disk drive the item Legacy
Diskette A must be set to 1.44/1.25MB 3 1/2.
System Installation
and Upgrade >> System Installation
SYS-CP842-1.0E 7-3
[Advanced] Screen
Specify the [Advanced] screen settings as shown below.
I/O Device Configuration
PCI Configuration
Installed O/S: Other
Reset Configuration Data: Yes*1
Secured Setup Configurations:No
Large Disk Access Mode: DOS
PS/2 Mouse: Auto Detect
Legacy USB Support: Disabled
Halt on Watchdog Timer:Disabled
Watchdog Timer Interrupt:Auto
Go to the ‘‘I/O Device Configuration sub-menu by selecting the item and pressing
[Enter], then verify that the settings are as shown below.
Local Bus IDE adapter: Both
Serial port A: Auto
Serial port B: Auto
Parallel port: Disabled
Floppy Disk controller: Disabled*2
Onboard Ethernet controller: Enabled
Onboard USB controller: Disabled
Note: *1 : The Reset Configuration Data item is reset to No when the BIOS settings are completed,
and must therefore be set to Yes each time the BIOS Settings screen is displayed.
*2 : Set the “Floppy Disk Controller” to “Enabled” when using the optional floppy disk drive.
Go to the ‘‘PCI Configuration sub-menu by selecting the item and pressing [Enter],
then verify that the settings are as shown below.
PCI IRQ line 1: 11
PCI IRQ line 2: 5
PCI IRQ line 3: 10
PCI IRQ line 4: 9
System Installation
and Upgrade >> System Installation
7-4
SYS-CP842-1.0E
[Power] Screen
Specify the [Power] screen settings as shown below.
Power Savings: [Disabled]
Idle Mode: Off
Standby Timeout: Off
Auto Suspend Timeout: Off
Hard Disk Timeout: Disabled
Resume On time: [Off]
Resume time: [00:00:00]
Resume Date: [00/00/0000]
[BIOS] Screen
The [Bios] screen shows various types of information, but settings at this screen can-
not be changed.
[Boot] Screen
Arrange the order of the items as shown below. To change an items order, select the
item (highlighted), then use the [+] and [-] keys to move the item up and down, respec-
tively.
To avoid a startup from the floppy disk (in systems with a floppy disk drive), select
Removable Devices, then press [Shift] + [1] to enter an exclamation mark (!) in front of
Removable Devices as shown below.
! Removable Devices
ATAPI CD-ROM Drive
Hard Drive
Network Boot
[Exit] Screen
When the settings described above have been made, select the first item Exit Saving
Changes and press [Enter] key. Select Yes at the confirmation message to register the
settings.