4OM-1429-008_w.pdf - 第140页
2-7 0712-002 2.2 List of W arning Messages W arning Codes Display Field A (Scope of W arning Messages) Display Field B (Details of W arning Messages) 01 1001 Empty Feeder (rear) Please set the feeder (rear) that used by …
2-60707-001
2.2 List of Warning Messages
Warning Codes Display Field A (Scope of Warning Messages)
Display Field B (Details of Warning Messages)
010f21 P.C.B. existence
There is no P.C.B on the central conveyor.
010f22 P.C.B. existence
There is no P.C.B on the positioning 2conveyor.
010f23 P.C.B. existence
There is no P.C.B on the inlet and outlet of output cnvr.
010f24 P.C.B. existence
There is no P.C.B that can be transported.
010f25 P.C.B. existence
Two P
.C.Bs were detected on the supply conveyor. Please remove the P.C.B of the
conveyor entrance.
010f26 P
.C.B. existence
Two P.C.Bs were detected on the output conveyor. Please remove the P
.C.B on the
conveyor.
010f27 P.C.B. existence
The P
.C.B was detected on the inlet of input buffer. Please remove the P
.C.B.
010f28 P.C.B. existence
The P.C.B was detected on the positioning 1conveyor. Please remove the P.C.B.
010f29
P.C.B. existence
The P.C.B was detected on thecentral conveyor. Please remove the P.C.B.
010f30 P.C.B. existence
The P
.C.B was detected on thepositioning 2conveyor. Please remove the P.C.B.
010f31 P.C.B. existence
The P.C.B was detected on the output conveyor Please remove the P
.C.B.
010f32 P.C.B. existence
There are no P.C.B to finish at the same time. Please remove all P
.C.B in a
positioning position whether you install a there.
010f33 P.C.B. existence
A P.C.B to fi
nish at the same time is not prepared on positioning 1 conveyer. Please
remove all P.C.B whether to be put.
010f34 P.C.B. existence
A
P.C.B to finish at the same time is not prepared on central conveyer. Please
remove all P
.C.B whether to be put.
010f35 P.C.B. existence
A P.C.B to fi
nish at the same time is not prepared on positioning 2 conveyer. Please
remove all P.C.B whether to be put.
010f36 P.C.B. existence
A P.C.B was detected at the inlet of the input buf
fer conveyor. Please remove it.
010f37 P.C.B. existence
A P.C.B. was detected at the inlet of the output buffer conveyor
. Please remove it.
010f38 P.C.B. existence
A P.C.B was detected at the outlet of the input buffer conveyor. Please remove it.
010f39
P.C.B. existence
A P.C.B. was detected at the outlet of the output buffer conveyor. Please remove it.
2-70712-002
2.2 List of Warning Messages
Warning Codes Display Field A (Scope of Warning Messages)
Display Field B (Details of Warning Messages)
011001 Empty Feeder (rear)
Please set the feeder (rear) that used by the pattern program.
011002 Empty Feeder (rear)
-----
011101 Empty Feeder (front)
Please set the feeder (front) that used by the pattern program.
011102 Empty Feeder (front)
-----
011201 Transfer main circuit
Press [POWER ON] button to activate Load Power circuit.
011202 Transfer main circuit
Press [POWER ON] button to activate Load Power circuit.
011301 Transfer main circuit (backup, width setup)
Press [POWER ON] button to activate Load Power circuit.
011302 T
ransfer main circuit (backup, width setup)
Press [POWER ON] button to activate Load Power circuit.
011401 Zeroing not finish
Perform
All zeroing
011501 Feeder communication not fi
nish (rear)
Please wait for a while.
011601 Feeder communication not fi
nish (front)
Please wait for a while.
011701 P
.C.B. position
Please position the P.C.B.
011702
P.C.B. position
Please locate the P.C.B in positioning 1.
01
1703 P.C.B. position
Please locate the P.C.B in positioning 2.
011704 P
.C.B. position
Please position the P.C.B of stage 2 in positioning 1.
011705
P.C.B. position
Please position the P.C.B of stage 1 in positioning 2.
011706 P.C.B. position
There is no P.C.B. in the setting position.
011801 Data transfer not finish
It cann't start because data is not set properly.
011901 Head unsettled comp. confirmation
An unsettled component was detected. Please discard the component. In case of
the "Pauses" condition, perform the operation for interruption.
01
1a01 Nozzle stocker lower limit confirmation
Please perform All zeroing.
011b01 NL axis zero confirmation
Please perform All zeroing.
2-80707-001
2.2 List of Warning Messages
Warning Codes Display Field A (Scope of Warning Messages)
Display Field B (Details of Warning Messages)
011b02 NL axis zero confirmation
The top and bottom axis (NL, L) by which a failure setup is carried out has fallen.
Since a zeroing cannot be performed, please raise it above a pass line manually.
011c01 Nozzle arrangement confirmation (rear)
The nozzle arrangement of the Current Program and the head (rear) is different.
011d01 Nozzle arrangement confirmation (front)
The nozzle arrangement of the Current Program and the head (front) is different.
011e01 Feeder reload (rear)
Please reload the feeder that has shortage of comp.
011f01 Feeder reload (front)
Please reload the feeder that has shortage of comp.
012001 Recycling Conveyor (rear)
The recycle conveyor (rear) is filled up. [B0924]
012101 Recycling Conveyor (front)
The recycle conveyor (front) is filled up. [B0924]
012201 Comp. Trash Box (rear)
The comp. trash box (rear) is filled up. [B0925]
012301
Comp. Trash Box (front)
The comp. trash box (front) is filled up. [B0925]
012501 Data check
Error was found in internal data of the control. Please change the model or try to
save the system data.
012601 Recycling Conveyor (rear)
Please connect the recycling conveyor (rear).
012701 Recycling Conveyor (front)
Please connect the recycling conveyor (front).
012801 Tray safety door (rear)
Please close tray safety door and push tray ready sw(rear).
012901
Tray safety door (front)
Please close tray safety door and push tray ready sw(front).
012a01 Tray shotage Comp (rear)
Please supply comp, close tray door(rear) and push tray ready sw(rear).
012b01 Tray shotage Comp (front)
Please supply comp, close tray safety door and push tray ready sw(front).
012c01 PCB Size X
Please check the PCB size X of pattern program data.
012d01
PCB Size Y
Please check the PCB size Y
of pattern program data.
012e01 Magazine existence, Type difference
Please check the existence of a magazine, or the number of stages of a magazine.
012f01 Magazine existence, Type difference
Please check the existence of a magazine, or the number of stages of a magazine.