4OM-1429-008_w.pdf - 第154页
2-21 0707-001 3.2 List of Machine Information Machine Information Codes Display Field A (Scope of Machine Information) Display Field B (Details of Machine Information) 801d01 Semi-auto(continue) start mode auto change Pr…
2-200707-001
3.2 List of Machine Information
Machine
Information Codes
Display Field A (Scope of Machine Information)
Display Field B (Details of Machine Information)
801a01 Warning Operation
Product started by RUN MODE "PASS"Operation.
801a02 Warning Operation
The P.C.B. before component placing was conveyed from X/Y table.
801a03 Warning Operation
The P.C.B. in the middle of component placing was conveyed from X/Y table.
801a04 Warning Operation
The feeder ready button was turned on in start protection mode.
801a05 Warning Operation
Cannot alternate by external start protection.
801b01 Lightning Surge Warning
Lightning Surge Protector works; Q204.
801b02 Lightning Surge W
arning
Lightning Surge Protector works; Q204. Running continue.
801c01 Information
This placement step was detected outside of the possible range. This step is auto
skip running.
801c02
Information
Feeder carriage has been paused to avoid clash with missing component. Please
collect component before operating the feeder carriage.
801c03 Information
Data was changed during machine worked. The changed data is not reflected in
operation until it stops or interrupts operation.
801c04
Information
PCB Origin Position data is not right. Please correct a PCB Origin Position on a
"Prod Chng(Origin Pos)" screen.
801c05 Information
Warm start mode was canceled.
801c06 Information
The machine stopped by the automatic stop function.
801c07 Information
Warm start mode was canceled. Please remove the unaccomplished P.C.B.
801c08 Information
It started with the data out of the setting range contained in the feeder offset B
data of system data. On edit screen, X/Y of the components (tape width 8mm /
sending pitch 2mm) should be set as more than -1.0mm and less than+1.0mm.
801c09 Information
It started with the data out of the setting range contained in the placement level
d
ata of
comp
onent
suppl
y changed data. On edit screen, the place level of square
shape below 3216 should be set up less than +0.5mm. When the place level
exceeding 0.5mm is required, please input H data of placement data (PP data).
2-210707-001
3.2 List of Machine Information
Machine
Information Codes
Display Field A (Scope of Machine Information)
Display Field B (Details of Machine Information)
801d01 Semi-auto(continue) start mode auto change
Production operation was interrupted for the state where PCB before component
are placed exists on XY table.
801e01 Placement Level Data
Calculated data out of range. Please check library data and pattern program data.
801f01 Warm start mode auto change
Operation was
can
celed for the state where the P.C.B. in the middle of component
placing is on X/Y table.
802001 Alarm for Splicing
Few components to feed. Please prepare Splicing.
802101 Feeder Maintenance Warning
The total number of feeder's shots reached a previous notice setting number.
802102 Feeder Maintenance Warning
The feeder adsorption rate decreased and exceeded the previous notice setting
number.
2-220707-001
3.2 List of Machine Information
Machine
Information Codes
Display Field A (Scope of Machine Information)
Display Field B (Details of Machine Information)
803001 FAN Stop Warning
The ceiling cooling fan stopped.
803002 FAN Stop Warning
The lower mount (left fornt) cooling fan stopped.(M105)
803003 FAN Stop Warning
The lower mount (left rear) cooling fan stopped.(M106)
803004 FAN Stop Warning
The upper mount (left front) cooling fan stopped.(M107)
803005 FAN Stop W
arning
The upper mount (left rear) cooling fan stopped.(M108)
803006 FAN Stop Warning
The lower mount side (left front) cooling fan stopped.(M109)
80300
7 FAN Stop Warning
The lower mount side (left rear) cooling fan stopped.(M1
10)
803008 FAN Stop W
arning
The CPU2 control box (left) cooling fan stopped.(M111)
803009
FAN Stop Warning
Fan stop detection satellite [STLT_F
AN_MON] It does not answer. A fan stop is
normally undetectable.
80300a
FAN Stop Warning
The conveyor multi-axis amplifier (left) cooling fan stopped.(M122)
80300b
FAN Stop Warning
The lower mount side (right front) cooling fan stopped.(M116)
80300c F
AN Stop Warning
The lower mount side (right rear) cooling fan stopped.(M117)
80300d FAN Stop Warning
The recognition BOX cooling fan stopped.(M1
18)
80300e FAN Stop Warning
The electrical system box power supply cooling fan (left) stopped.(M119)
80300f
FAN Stop Warning
The electrical system box power supply cooling fan (right) stopped.(M120)
803010 F
AN Stop Warning
The ceiling (left front) cooling fan stopped.(M102)
803011 F
AN Stop Warning
The ceiling (left rear) cooling fan stopped.(M101)
803012 FAN Stop W
arning
The ceiling (right front) cooling fan stopped.(M104)
803013 FAN Stop W
arning
The ceiling (right rear) cooling fan stopped.(M103)
803014 F
AN Stop Warning
The lower mount (right fornt) cooling fan stopped.(M112)
803015 FAN Stop W
arning
The lower mount (right rear) cooling fan stopped.(M113)