4OM-1429-008_w.pdf - 第186页
3-25 3.3 Conveyor 0707-001 Erroe ID Error Name, Description, Cause, and Remedy 425101 Output Cnvr . Overtime The P .C.B. transport (carry in) from Cnvr . Positioning2 did not end in prescribed time. Please continue the w…
3-24
3.3 Conveyor
0707-001
Erroe ID Error Name, Description, Cause, and Remedy
424314 Cnvr. Positioning2 Error
The pickup OFF of a P.C.B went wrong.
-----
424315 Cnvr. Positioning2 Error
Slowdown operation was not carried out at the time of carrying-in operation.
Please check whether the sensor of a conveyor is operating normally and check
whether a P.C.B can convey normally by manual conveyance.
424316 Cnvr. Positioning2 Error
Rise operation of a reversal PCB locate stopper is not completed.
Please check a stopper.
424317 Cnvr. Positioning2 Error
Downward operation of a reversal PCB locate stopper is not completed.
Please check a stopper.
424318 Cnvr. Positioning2 Error
The P.C.B was transported a predetermined distance, but the operation was not
completed.
There is a possibility that the P
.C.B fell over from conveyer whether a board is
caught. Please confirm it over a conveyer.
424319
Cnvr. Positioning2 Error
The process of inside signal between conveyors failed.
Please continue the work after checking the P.C.B on a conveyor.
4243
20 Cnvr. Positioning2 Error
The P.C.B. transfer operation could not start.
-----
4243
21 Cnvr. Positioning2 Error
An error was detected in transferring the P
.C.B..
Please continue the work after checking the P.C.B on a conveyor.
424322 Cnvr. Positioning2 Error
Speed reduction was not performed during transferring operation.
Please return the P.C.B. to the proper position when it is sitting between the
conveyors otherwise, remove the P.C.B.
And, the P.C.B. detection sensor might
have had a wrong detection, so please check it to make detections correctly
424323 Cnvr
. Positioning2 Error
A servo error was found in the movement that the backup base was rising. The
backup jig and pins may be left under the transfer rail.
Cancel the error and perform zeroing operation after that, open the cover to
remove the left backup jig and pins under the transfer rail. Perform the setup
operation again to set the backup jig and the pins to the proper positions.
424324 Cnvr
. Positioning2 Error
Support pins /Jig were detected before the backup base starts to rise.
Remove the support pins / jig from the backup base. If the removong operation is
difficult, perform the function to move the support pin changing position.
3-25
3.3 Conveyor
0707-001
Erroe ID Error Name, Description, Cause, and Remedy
425101 Output Cnvr. Overtime
The P.C.B. transport (carry in) from Cnvr. Positioning2 did not end in prescribed
time.
Please continue the work after checking the P.C.B on a conveyor.
425102 Output Cnvr. Overtime
The P.C.B. transport (exhaust) to output machine did not end in prescribed time.
Please continue the work after checking the P.C.B on a conveyor.
425103 Output Cnvr. Overtime
The movement to P.C.B. receiving position did not end in prescribed time.
-----
425104 Output Cnvr. Overtime
The movement to the arrangement position did not end in prescribed time.
-----
425105 Output Cnvr
. Overtime
The P.C.B. transport (carry in) from Cnvr. Positioning1 did not end in prescribed
time.
Please continue the work after checking the P.C.B on a conveyor.
425106 Output Cnvr
. Overtime
The reversal positioning operation did not end in prescribed time.
Please continue the work after checking the P.C.B on a conveyor.
425107 Output Cnvr
. Overtime
The conveyor upper cover by output side has opened.
Please close the cover. Production can be continued.
425201 Output Cnvr
. P.C.B. Detection
P.C.B.'s were at inlet and outlet of cnvr
.
Please continue the work after checking the P.C.B on a conveyor.
425202 Output Cnvr. P.C.B. Detection
There is no P.C.B. on the Cnvr
. The P.C.B. fell while moving to the receiving
position.
Please continue production after checking whether the P.C.B has fallen around a
conveyor.
425203 Output Cnvr. P
.C.B. Detection
There is no P.C.B. on the Cnvr. The P.C.B. was removed.
-----
425204 Output Cnvr. P
.C.B. Detection
There is a P.C.B. on the Cnvr. The P.C.B. could not be discharged.
Please continue the work after checking the P.C.B on a conveyor.
425205 Output Cnvr. P
.C.B. Detection
There is no P.C.B on the conveyer. After the P.C.B. carrying in ended, it can not
able to be detected.
Please continue the work after checking the P.C.B on a conveyor.
425206
Output Cnvr. P.C.B. Detection
The P.C.B. was detected by the conveyer entrance sensor.
Please continue the work after checking the P.C.B on a conveyor.
3-26
3.3 Conveyor
0707-001
Erroe ID Error Name, Description, Cause, and Remedy
425207 Output Cnvr. P.C.B. Detection
The P.C.B. was detected with the conveyer exit sensor.
Please confirm the P.C.B on the conveyer.
425208 Output Cnvr. P.C.B. Detection
The exhaust end board sensor of a conveyor exit detected the P.C.B.
Please check the P.C.B on a conveyor.
425209 Output Cnvr. P
.C.B. Detection
The exhaust end board sensor of a conveyor exit did not detect P.C.B during
discharge operation.
Please check the sensor.
425210 Output Cnvr. P.C.B. Detection
Manual bypass of the P.C.B was carried out in the state where a P.C.B is on a
conveyor.
Please remove the P.C.B carried out manual bypass. Production can be
continued.
42521
1 Output Cnvr. P.C.B. Detection
The P.C.B was not found in the proper position.
Please remove the P.C.B on a conveyor. Production can be continued.
425212
Output Cnvr. P.C.B. Detection
Manual bypass of the P.C.B was carried out.
Please remove the P
.C.B carried out manual bypass. Production can be
continued.
425213 Output Cnvr. P.C.B. Detection
P.C.B on a conveyer was removed in output sync / alternation output process.
Please do reproduction after making the P
.C.B return to original state.
425214 Output Cnvr. P.C.B. Detection
The state of a P.C.B on conveyer changed in output sync / alternation output
process.
Please do reproduction after making the P.C.B return to original state.
425215
Output Cnvr. P.C.B. Detection
The P.C.B was detected with the conveyer entrance sensor.
Please return the P.C.B. to the proper position when it is sitting between the
conveyors otherwise, remove the P
.C.B. And, the P.C.B. detection sensor might
have had a wrong detection, so please check it to make detections correctly
425216 Output Cnvr. P
.C.B. Detection
The P.C.B. was detected before carrying-in operation.
Restart the product operation after removing the P.C.B. when it is on the
conveyor.
425217 Output Cnvr
. P.C.B. Detection
A P.C.B. was detected with the conveyor entrance sensor upon completion of the
output operation.
After checking the P.C.B. on the conveyor, continue the product operation. If no
P.C.B. is there, remove the factor why the sensor was detected upon completion
of the output operation.