4OM-1429-008_w.pdf - 第26页

Safety Precautions Safe-15 ALFE-ID Alert Indications described as " " (continuted) Alert Description Related Items The load power to the motors, etc., is turned OFF but the setup operation must be performed car…

100%1 / 279
Safety Precautions
Safe-14
ALFE-ID
Alert Indications described as " " (continuted)
Alert Description Related Items
When a tape feeder is attached or detached, be sure not to
drop it.
Otherwise, a foot injury will result or the feeder itself may be
damaged.
Carefully handle each feeder one by one and do not drop any.
"2.4.8" in
"Chapter 1 (Vol. 1)"
"2.1" in
"Chapter 2 (Vol. 1)"
"2.4" in
"Chapter 3 (Vol. 1)"
Hazardoustoyourhandsandngers!
Be sure to hold the handle to move the bank feeder change cart.
"2.4.8" in
"Chapter 1
(Vol. 1)"
"2.4" in
"Chapter 3 (Vol. 1)"
W
atchyourstep!
·
Be careful not to hit your foot against the cart while moving the bank
feeder change cart.
Especially, the resistance against cart movement may change rapidly
when the oor is ragged and the cart gets caught on the oor or
a sheet is used and the cart gets caught at the edge or a slackened
portion of the sheet.
"2.4.8" in
"Chapter 1 (Vol
. 1)"
"2.4" in
"
Chapter 3 (Vol. 1)"
Do not put your hand in the moving area while the feeder base is
moving up or down.
While the LED of a [FEEDER READY] switch is being ickering, it
indicates that the corresponding feeder base is moving up and down.
"2.4.8" in
"Chapter 1 (Vol. 1)"
Be sure to wear gloves during cleaning. Otherwise, you may cut your
hands on the edges of the lighting hood.
"2.4.9" in
"Chapter 1 (Vol. 1)"
"3.3.3" in
"Chapter 1 (Vol. 4)"
Before starting the automatic operation, check carefully that there is no
person around the machine (especially on the other side of the machine
operation). Make sure that no objects (tools, parts, etc.) are left behind.
"1.1.3" in
"Chapter 2 (Vol. 1)"
The padlock key should be kept in such a way that nobody except the
personnel in charge of maintenance can supervise it.
"1.4.3" in
"Chapter 2 (Vol. 1)"
CAUTION
0712-002
Safety Precautions
Safe-15
ALFE-ID
Alert Indications described as " " (continuted)
Alert Description Related Items
The load power to the motors, etc., is turned OFF but the setup
operation must be performed carefully when you put your hand
inside the machine.
"3.3.1", "3.3.2" and
"3.6" in "Chapter 3
(Vol. 1)"
This setup operation must be performed with your hands inserted
inside the machine.
Open the cover(door type) and perform the setup operation with
the load power supply to the servomotor being turned "OFF".
"5.1.2" in
"Chapter 4 (Vol. 2)"
In this teaching operation, the cover of the light source device
need not be opened.
Do not open the cover of the light source device.
The cover of the light source device, when opened, exposes users to the
high voltage components and may result in electrical shocks.
"6.5.15" in
"Chapter 4 (Vol. 2)"
•
Even when the power breaker is set to "OFF", the primary line
is powered, making it possible to cause an electric shock.
Be sure to completely stop the power supply to the machine before
maintenance work.
"1.1" in
"Chapter 1 (Vol. 4)"
•
Residual voltages may remain behind for a few minutes in the
internal devices of the machine after power interception.
Before performing maintenance work, wait until the charge lamps of
the DC power supply and the servoamplier go "OFF" in 10 minutes
or more after the power breaker is set to "OFF".
"1.1" in
"Chapter 1 (Vol. 4)"
When the at ring is cut, take care not to get injured by the
commercially available cutter.
"3.3.6" in
"Chapter 1 (Vol. 4)"
Your hand might be cut at the edge of the linear guide in the
cleaning operaiton. Wear gloves.
"3.3.8" in
"Chapter 1 (Vol. 4)"
The load power to the motors, etc., is turned OFF but the
maintenance operation must be performed carefully, protecting
your hands from any injury.
"4.5" in
"Chapter 1 (Vol. 4)"
0805-003
CAUTION
Safety Precautions
Safe-16
ALFE-ID
Alert Indications described as " " (continuted)
Alert Description Related Items
The light emitter of the linear measure sensor is made of glass.
If the light emitter happens to be damaged, be sure to suck up
the fragments with a vacuum cleaner, etc.
Do not collect the fragments with your bare hands to protect your
hands from injuries.
"4.5" in
"Chapter 1 (Vol. 4)"
CAUTION
0805-003