2500_Users_Manual.pdf - 第413页
ProM aster 25 00 User Manua l F-1 F Local Mode Local mode is an operati ng mode for the P roMaster 2500 where the operator is com municating usin g the 2500’s k eyboard an d display. Thi s mode can be used for initi al s…
Computer Remote Control
E-24 ProMaster 2500 User Manual
9B Incompatible system/algorithm disks or incompatible device
libraries
9C Invalid command for this mode
9D I/O address beyond range of data format selected
A1 No Electronic ID
A2 Electronic ID verify error
AB Unable to load system file from system disk
AC Security violation
AE Keep Current algorithm disk not found. Insert your Keep Current
algorithm disk
AF Operation not allowed because the device was selected by family/
pinout code
B0 Capacitor configuration error
B1 Block not allowed for bulk erase
B2 Partial device operation not allowed
B4 Odd Memory Begin Address or User Data Size Incompatible with
Data Word Width
B6 Algorithm doesn’t have a footnote
B8 Algorithm or Logic disk not found
B9 Algorithm disk 2 or Memory disk not found
BA Yield Tally access/update error
BC Last device operation checksum not available
D5 Port Transfer Error
E30Ribbon not detected
E31Ribbon latch not engaged
FE Undefined error
FF Operation aborted at programmer
ProMaster 2500 User Manual F-1
F
Local Mode
Local mode is an operating mode for the ProMaster 2500 where the
operator is communicating using the 2500’s keyboard and display. This
mode can be used for initial system setup, running diagnostic tests or
cycling devices. This chapter describes the parameters that can be
changed using the 2500’s keyboard.
Switching Between Local and Remote Modes
The 2500 normally operates with TaskLink in Remote mode. To switch to
Local mode, press
LOWER CASE
+
L
(for
Local
) on the 2500’s keyboard.
The 2500 powers up in the mode it was in when last turned off.
Return to Remote mode by pressing
LOWER CASE
+
R
(for
Remote
) on
the 2500’s keyboard.
System Configuration
The ProMaster 2500 can be configured to operate with either a dot matrix
or a thermal printer. The handler was configured correctly at the factory
for the type of printer that was installed during assembly. If a handler
with a thermal printer begins operating as though it were configured for
the dot matrix printer option, complete the following steps to reconfigure
it for the thermal printer.
1. Press
LOWER CASE
+
L
to put the 2500 in local mode.
2. From the Main Menu, press
LOWER CASE
+
W
.
1-DOT MATRIX, 2-THERMAL
ENTER TYPE OF MARKER (2): _
Local Mode
F-2 ProMaster 2500 User Manual
3. Press
2
to select the thermal printer. This reconfigures the 2500 so that
it operates with a thermal printer installed.
The Main Menu Commands
The 2500 will display the following Main Menu:
Press the number key corresponding to the optional menu you wish to
access and the 2500 will display the new menu. This manual will describe
these menus in the order that these appear on the display from top to
bottom.
Operations Menu
This menu lists operations that instruct the 2500 to perform an operation.
From the Main Menu, press one of the numbers to select the option you
need to access.
The Device Programming
Operations
These commands are not to be used during normal operation. They are
available to the service technician to perform tests to assist in assessing
programming related problems. The service commands on this menu are:
•Program/Test & Label
•Load Master
• Program/Test Only
Label Only
This command is useful when you want to print and apply labels to
devices. When this is selected, the programming station is bypassed. All
devices are labeled and directed to the nearest receiving tube. Category
assignments are inactive in this mode.
1. From the Main Menu, press
1
to select OPERATIONS. The 2500
displays:
2. From the Operations Menu, press
4
to select LABEL ONLY. The 2500
displays:
* * PROMASTER 2500 MAIN MENU * *
ENTER THE NUMBER OF THE DESIRED FUNCTION
1 - OPERATIONS 3 - SYSTEM SETUP
2 - FILE UTILITIES 4 - DIAGNOSTICS
* * * OPERATIONS MENU * * *
1 - PROGRAM/TEST & LABEL 4 - LABEL ONLY
2 - LOAD MASTER 5 - PRINT ONLY
3 - PROGRAM/TEST ONLY 6 - PURGE
LABEL ONLY
TEMPORARY FILE1 FILE2 FILE3
FILE4 FILE5 FILE6 FILE7
ENTER FILE NAME: