M20_Ope_E.pdf - 第415页

Chapter 14 Intelligent Feeder 14-15 14-2-10 Checking the Station This section explains how to find the lane (feeder) in which a component is to be set. Action: ① Scan the "Show / Hide" barcode to display the ID…

Chapter 14 Intelligent Feeder

14-14

14-2-7 Deleting a Component Barcode

This section explains how to delete a component barcode that has been registered.

Action:

① Scan the "Show / Hide" barcode to display the ID registration window (InputBar).

② Scan the component’s barcode.

③ Scan the "Delete Comp. Barcode" barcode.

④ A message “Execute the Delete Command?” will appear, so click <Yes>.

⑤ “OK” will be displayed if the barcode has been deleted successfully. If deletion has failed,

read the displayed message, make necessary corrections, and then scan the "Delete Comp.

Barcode" barcode again.

⑥ Scan the "Show / Hide" barcode to close the ID registration window (InputBar).

Note: Deletion of component barcode is only possible while production is not run.

The feeder linked with the component barcode to be deleted will be deregistered. The

deregistered feeder needs to be re-registered to the database.

14-2-8 Inquire Database

This section explains how to check the component barcodes that have been linked with feeder

barcodes (ID).

Action:

① Scan the "Show / Hide" barcode to display the ID registration window (InputBar).

② Scan the feeder’s barcode.

③ Scan the "Inquire Database" barcode.

④ If the database is referred to successfully, the results will be displayed, so check them.

→If the scanned feeder barcode (ID) is not linked with a component barcode, a message

“This Feeder barcode is not registered in ID Database” will appear.

⑤ Scan the "Show / Hide" barcode to close the ID registration window (InputBar).

14-2-9 Compare Database

This section explains how to check whether the combination of a component code and a feeder

barcode (ID) is correct.

Action:

① Scan the "Show / Hide" barcode to display the ID registration window (InputBar).

② Scan the feeder’s barcode.

③ Scan the component’s barcode.

④ Scan the "Compare Database" barcode.

⑤ The verification result will be displayed, so check it.

“OK” will be displayed if the combination is correct.

→If the combination is not correct, a message “Relation between Feeder and Comp. is

improper.” will appear and the correct component barcode will be displayed.

⑥ Scan the "Show / Hide" barcode to close the ID registration window (InputBar).

Chapter 14 Intelligent Feeder

14-15

14-2-10 Checking the Station

This section explains how to find the lane (feeder) in which a component is to be set.

Action:

① Scan the "Show / Hide" barcode to display the ID registration window (InputBar).

② Scan the component’s barcode.

③ Scan the "Check Station" barcode.

④ The result will be displayed in a message window, so check it.

→If a feeder has already been set in the target lane, the LED will indicate the confirmation

status (light blue/flash) temporarily.

→For instance, a component (1005C), that is to be set in lane 34 on the front feeder bank, is

set in lane 30, a message window will appear showing: ① the lane No. in which the

component has been set by mistake, ② the correct lane No., and ③ the component name.

[Feeder position error. ST-F-30 -> ST-F-34"1005C" ID:62-20]

① ② ③

Note: The station check command can be accepted only while production is halted.

The station check function can be executed, for instance, just after <Run> button in the

production window is clicked to start production, and after production is halted to exchange

components. (In either case, production will remain halted until the [Start] button on the

mounter is pressed.)

Chapter 14 Intelligent Feeder

14-16

14-3 Running the Server Software

14-3-1 What is the Server Software?

The server software (CompSvr.exe) controls the ID database (relationship between feeder IDs

and component barcodes) and component table (relationship between component barcodes

and component codes). It also contains a barcode creation software program as a part of its

function to enable creation of command, feeder and component barcodes.

Here explains how to run the server software.

Server Software Window

14-3-2 Starting/Exiting the Server Software

■Starting

Double-click the server software icon on the Windows taskbar.

■Exiting

To exit the server software, select File > Exit from the taskbar.

When the server software is exited, connection between the barcode input software and client

software will be shut off. To use the intelligent feeder function again after the software is exited,

restart the mounter if it has been run on the mounter. In the case of PC, from the Windows

taskbar, select Start > Program > Intelligent Tool > CompSrvr.