M20_Ope_E.pdf - 第451页

%d8 Step:%d5 Offset:%d6 pressure. 1439 Clamp MX-ST2. Clamp MX-ST2. Check ANC shutter and missetting of nozzle. Contact 1385 ANC scanning error us for ANC scanning error. 1386 MX-40 pallet setting error Check pallet infor…

1384 ANC operation error

Check ANC shutter and missetting of nozzle. Contact

us for ANC scanning error.

1339 Communication error in image process

1340

1341

Component lack. Setup is possible %s #%d1

Pickup points of component lack are displayed.

Replenish components.

Vision process sequence error. Execute system

1342

recovery.

Check Vision processing unit or Cables for error.

1343 Failed to clamp MX-ST2. Failed to clamp MX-ST2.

1344 Failed to unclamp MX-ST2. Failed to unclamp MX-ST2.

1345 %s pallet setting error (Pallet-%d2) Check pallet information or MXR.

1346

1347

%s origin acquisition error (Pallet-%d2)

Cannot supply components from %s.

Check conditions of MXR.

Check the feeder.

The feeder is specified as unavailable feeder. %s Clear the Feeder Skip state for concerned pickup

1348

1349

#%d1

AMF measurement ends.

point(s).

1350 Setup error

This error is caused by effect of other errors. Check

the other error messages near around.

1351

Retry step postpone table is full. Execute normal

retry process.

Retry step postpone table is full. Execute normal

retry process.

MAP measurement ends. Press Start SW to convey

1352 MAP measurement ends.

out the board.

1353

1354

Axis movements are unstable.

There are no usable pickup points because the

1355 machine is in the changeover state. (%m %s-%d3

Head%c1 Nozzle No.%d2 Step:%d5 Offset:%d6)

End the changeover state.

1356 Reject conveyor on %s %d1 is almost out of space.

There are no usable pickup points because Feeder

Components on Reject conveyor are almost full.

(Warning!)

1357 Skip is/are specified. (%m %s-%d3 Head%c1 Nozzle

Clear the Feeder Skip state for concerned pickup

1358

No.%d2 Step:%d5 Offset:%d6)

Controller error

point(s).

System is not operating properly. Contact us.

Check the code entry equipment for settings and

1359 PCB code entry error connections. To continue the job run, check the PCB

code and select the program.

1360 %s Motor alarm

Execute Maintenance>ServoOff. Ten minutes later,

turn on <Servo> switch.

Coordinates exceeded the setting of

1361 %s position exceeded the limit. SystemParameter>WorkRange or

SystemParameter>Axis>TravelDist.

1362 %s detected EL(+). Overrun. Take origin again.

1363 %s detected EL(-). Overrun. Take origin again.

1364 Origin of %s is not taken. Check Origin menu.

1365

1366

%s error

Error occurs at %s.

Remove error.

1367 %m PCB code is not defined in the Plan.

Define the PCB code in the Plan and select the

program.

Fiducial correction was not performed. Change the

1368 Fiducial error (4point)

mark location.

1369

1370

Timeout in %s operation.

ANC slide channel operates improperly.

Check cylinders, motors, and sensors.

Check cylinders and sensors.

This nozzle station is not for removing nozzles from

1371 The nozzle cannot be removed from the head.

heads.

1372 Error occurs in image processing. Check image process system and communication

1373 Device cannot be initialized. Contact us.

1374

1375

Error in opening PS-BC shutter. %s (%d1)

Error in closing PS-BC shutter. %s (%d1)

Check the shutter mechanism of the bulk feeder.

1376 Main clamp is abnormal.

Check support pin for crash. Check adjust plate for

foreign matters.

Check PCB stopper for normal operation st Manual

1377 PCB stopper is abnormal.

menu.

1378 Rear clamp is abnormal. Check rear clamp for normal operation.

1379

1380

Side clamp is abnormal.

ANC shutter is abnormal.

Check side clamp.

Check ANC shutter.

Computing error for correction. Save Log file and

1381 Fiducial error (calculation)

1382

1383

Conveyor error

Disconnect the cable and air tube for the CFB.

Check conveyor transfer belts and motors.

%d8 Step:%d5 Offset:%d6

pressure.

1439 Clamp MX-ST2. Clamp MX-ST2.

Check ANC shutter and missetting of nozzle. Contact

1385 ANC scanning error

us for ANC scanning error.

1386 MX-40 pallet setting error Check pallet information or MX-40.

1387 MX-40 origin acquisition error Check MX-40.

1388 MX-40 shuttle contacts conveyor rail. Check conveyor rail position.

1389 Feeder cannot operate. Check feeder for misfeeding.

1390 Signal output operation error System is abnormal. Contact us.

1391

1392

PS-32A tape-peeling error %s (%d1)

PS-32A re-positioning error %s (%d1)

Check Feeder Setting or check the feeder.

PS-32A sequence clear command control error %s

1393

(%d1)

Check Feeder Setting or check the feeder.

1394 MX-20 pallet setting error (Pallet-%d1) Check pallet information or MX-20.

1395 MX-20 origin acquisition error (Pallet-%d1) Check MX-20.

1396 MX-F20 shuttle contacts conveyor rail. Check conveyor rail position.

1397 Failed to retract MX-40 pallet Check MX-40 setting and conditions of MX-40B

1398 Failed to retract MX-20 pallet (Pallet-%d1) Check MX-20 setting and conditions of MX-20F

1399 Failed to retract %s pallet (Pallet-%d2) Check pallet information or MXR.

1400 %m

1401 %s is open.

1402 %s is pressed.

1403 Origin detection starts.

1404 Sensor of the safety guard responded.

1405 Origin has been detected.

1406 Waiting for Board arrival at %s. Waiting for Board arrival.

1407 Board starts to enter at %s. Just started Board transfer in.

1408 Board has arrived at %s. Completed Board transfer in.

1409 IN sensor detects board.

1410 Buffer sensor detects board.

1411 Arrival sensor detects board.

1412 OUT sensor detects board.

1413 Board clamp starts.

1414 Board clamp ends.

1415 Board unclamp starts.

1416 Board unclamp ends.

1417 Board is ready to be conveyed out at %s. Board is ready to be conveyed out.

1418

1419

Board starts to be conveyed out at %s.

Board has been away from %s.

Just started Board transfer out.

Completed Board transfer out.

1420

Canceled the job with the multiple-pickup cycle

halfway done.

When production is cancelled without completing

Cannot handle the multiple-pickup cycle by normal

resume procedure.

1421 postponed components, restart the production by

selecting Continue"."

Postponed components cannot be placed by selecting

Start from the selected row.""

1422 Canceled the job with components being picked up.

Remove the picked up components to resume

production.

No program step to execute. Pass the PCB through. No program step to execute due to component skip

1423

%s or etc. Check components.

1424 Waiting for Board arrival at %s. Waiting for Board arrival.

1425

1426

Board starts to enter at %s.

Board has arrived at %s.

Just started Board transfer in.

Completed Board transfer in.

1427

Pickup error %m %s-%d3 Head%c1 Nozzle No.%d2

%d7 < %d8 Step:%d5 Offset:%d6

Check status of Head, Component, and Pickup point.

1428

Pickup error (no countermeasure) %m %s-%d3

Head%c1 Nozzle No.%d2 %d7 < %d8 Step:%d5

Choke pressure error Head%c1 Nozzle No.%d2 %d7

1429

> %d8

Nozzle is choked.

1430 Feeder indexing starts.

1431 %s can be set up. Replenish components.

1432 Feeder indexing ends.

1433 %s waits to be unloaded.

1434

1435

Unloading PCB from %s starts.

Unloading PCB from %s is complete.

1436

Coplanarity measurement error %m %s-%d3 Head%c1

Nozzle No.%d2 Step:%d5 Offset:%d6

1437

On-head component is brought back (vision

inspection) %m %s-%d3 Head%c1 Nozzle:%d2

On-head component is brought back (pneumatic

Check the placement point and the nozzle for dirt.

1438 inspection) %m %s-%d3 Head%c1 Nozzle:%d2 %d7 >

Check that the nozzle is not choked. Check the air

offset. X:%d1 Y:%d2 Alarm:%d3 T:%d4 Alarm:%d8 range. Check the parameter setting.

1479

Dispense Nozzle Offset OK Head%c1 Angle:%d2 X:%d3

Y:%d4 T:%d5 The number of adjustments:%d8

1440 Unclamp MX-ST2.

Reached the limit of pickup or vision-process error

Unclamp MX-ST2.

1441 count. Feeder Skip %m %s-%d3 Head%c1 Nozzle:%d2

Step:%d5 Offset:%d6

Other feeder(s) will be used. The feeder will be

skipped from now on.

1442

Nozzle is detected on Head%c1. Does not agree with

inf. on Head-Nozzle Setup.

Nozzle change by hand is prohibited. Check if the tip

of the head is clean.

Nozzle is not detected on Head%c1. Does not agree

1443

1444

with inf. on Head-Nozzle Setup.

Nozzle change by hand is prohibited.

Specified number of PCBs have been produced. Press the Cancel switch to abort.

Failed to scan the PCB code. When a placed PCB is

1445

1446

unloaded, the mounter will pause by an error.

%m mode

The PCB code is scanned. When a placed PCB is

1447 unloaded, the program will be switched to the scanned

program.

Make settings of Dot Station Dispense Check in the

1448

1449

Dispense Check Data for Head%c1 is not found.

FL detect correction is disabled.

dispense check program.

FL detect correction is disabled in the user

1450

Both the FL detect correction and the vision

correction are enabled.

Select either FL detect correction or vision

correction.

Image processing result %m %s%c8 Head%c1 X:%d2

1451

Y:%d3 T:%d4 (%d5,%d6,%d7)

Component image is taken by camera.

1452 Setup of %s starts.

1453

1454

Setup of %s ends.

%s #%d1 component is set. (Components:%d2)

Updated the initial pickup point for %s [ #%d1 (P%d2#-

1455

%d3 pallet) ].

1456 %s CFB is locked.

1457 %s CFB is released.

1458

1459

%s pallet is returned.

The system switched to the %s mode.

1460

AMF Fiducial. Code:%d1 Group:%d2 X;%d3 Y:%d4 T:%d5

( %d6 %d7) %m

AMF Placement Head%d1 Angle:%d2 X:%d3 Y:%d4 T:%d5

1461

1462

(%d6 %d7 %d8) %m

Halt of head movement during PCB arrival wait %s

1463

Resumption of head movement on completion of PCB

arrival. PCB arrival wait time: %d1.%d4 seconds %s

1464

Area detection event error.(%d1 %d2:%d5 %d3->%d4

[%d8])

Obtain log data by clicking the <LOG> button and

1465

Axis status mismatch.(X:%d1 %d2->%d3 Y:%d4 %d5-

>%d6 [%d8])

Obtain log data by clicking the <LOG> button and

1466 The sensor detected the fluid shortage on Head%c1. Replenish the head with fluid in good time.

1467 Area interlock has been detected.

Obtain log data by clicking the <LOG> button and

1468

1469

1470

Switched to MX-40 upper stocker.

Switched to MX-40 lower stocker.

Timeout in temperature control for Head%c1 Check the temperature controller.

1471

Dispensing was started without the set temperature

being reached for Head%c1. Target:%v2deg C Check the temperature controller.

1472

Current:%v3deg C

Halt of Head%c1 movement for awaiting completion of

temperature control

1473

Short of OK counts for Head%s. OK count:%p2

Average ratio:%d3% Tolerance:%d4%-%d5%

Pressure:%v6Mpa Correction coefficient:%v1 %m

Number of retrials exceeded the Max Check Count

OK count < Min OK Count. Check the nozzle, syringe,

parameters.

1474

for Head%s. OK count:%p2 Average ratio:%d3% Number of retrials exceeded the specified Max Check

Tolerance:%d4%-%d5% Pressure:%v6Mpa Correction

coefficient:%v1 %m

Count. Check the nozzle, syringe, parameters.

1475

1476

Retry/Skip is not specified. Specify whether to retry or skip.

Measure DP %s( F:%d1 X:%d2 Y:%d3 AR:%d4 LS:%d5

1477

SS:%d6 SD:%d7 T:%d8 %m )

Dispense Nozzle Offset Adjustment Head%c1

1478

Angle:%d2 X:%d3->%d4 Y:%d5->%d6 T:%d7->%d8

Error in automatic acquisition of dispense nozzle Coordinates correction values exceeded the allowable