M20_Ope_E.pdf - 第452页

offset. X:%d1 Y:%d2 Alarm:%d3 T:%d4 Alarm:%d8 range. Check the parameter setting. 1479 Dispense Nozzle Offset OK Head%c1 Angle:%d2 X:%d3 Y:%d4 T:%d5 The number of adjustments:%d8 1440 Unclamp MX-ST2. Reached the limit of…

%d8 Step:%d5 Offset:%d6

pressure.

1439 Clamp MX-ST2. Clamp MX-ST2.

Check ANC shutter and missetting of nozzle. Contact

1385 ANC scanning error

us for ANC scanning error.

1386 MX-40 pallet setting error Check pallet information or MX-40.

1387 MX-40 origin acquisition error Check MX-40.

1388 MX-40 shuttle contacts conveyor rail. Check conveyor rail position.

1389 Feeder cannot operate. Check feeder for misfeeding.

1390 Signal output operation error System is abnormal. Contact us.

1391

1392

PS-32A tape-peeling error %s (%d1)

PS-32A re-positioning error %s (%d1)

Check Feeder Setting or check the feeder.

PS-32A sequence clear command control error %s

1393

(%d1)

Check Feeder Setting or check the feeder.

1394 MX-20 pallet setting error (Pallet-%d1) Check pallet information or MX-20.

1395 MX-20 origin acquisition error (Pallet-%d1) Check MX-20.

1396 MX-F20 shuttle contacts conveyor rail. Check conveyor rail position.

1397 Failed to retract MX-40 pallet Check MX-40 setting and conditions of MX-40B

1398 Failed to retract MX-20 pallet (Pallet-%d1) Check MX-20 setting and conditions of MX-20F

1399 Failed to retract %s pallet (Pallet-%d2) Check pallet information or MXR.

1400 %m

1401 %s is open.

1402 %s is pressed.

1403 Origin detection starts.

1404 Sensor of the safety guard responded.

1405 Origin has been detected.

1406 Waiting for Board arrival at %s. Waiting for Board arrival.

1407 Board starts to enter at %s. Just started Board transfer in.

1408 Board has arrived at %s. Completed Board transfer in.

1409 IN sensor detects board.

1410 Buffer sensor detects board.

1411 Arrival sensor detects board.

1412 OUT sensor detects board.

1413 Board clamp starts.

1414 Board clamp ends.

1415 Board unclamp starts.

1416 Board unclamp ends.

1417 Board is ready to be conveyed out at %s. Board is ready to be conveyed out.

1418

1419

Board starts to be conveyed out at %s.

Board has been away from %s.

Just started Board transfer out.

Completed Board transfer out.

1420

Canceled the job with the multiple-pickup cycle

halfway done.

When production is cancelled without completing

Cannot handle the multiple-pickup cycle by normal

resume procedure.

1421 postponed components, restart the production by

selecting Continue"."

Postponed components cannot be placed by selecting

Start from the selected row.""

1422 Canceled the job with components being picked up.

Remove the picked up components to resume

production.

No program step to execute. Pass the PCB through. No program step to execute due to component skip

1423

%s or etc. Check components.

1424 Waiting for Board arrival at %s. Waiting for Board arrival.

1425

1426

Board starts to enter at %s.

Board has arrived at %s.

Just started Board transfer in.

Completed Board transfer in.

1427

Pickup error %m %s-%d3 Head%c1 Nozzle No.%d2

%d7 < %d8 Step:%d5 Offset:%d6

Check status of Head, Component, and Pickup point.

1428

Pickup error (no countermeasure) %m %s-%d3

Head%c1 Nozzle No.%d2 %d7 < %d8 Step:%d5

Choke pressure error Head%c1 Nozzle No.%d2 %d7

1429

> %d8

Nozzle is choked.

1430 Feeder indexing starts.

1431 %s can be set up. Replenish components.

1432 Feeder indexing ends.

1433 %s waits to be unloaded.

1434

1435

Unloading PCB from %s starts.

Unloading PCB from %s is complete.

1436

Coplanarity measurement error %m %s-%d3 Head%c1

Nozzle No.%d2 Step:%d5 Offset:%d6

1437

On-head component is brought back (vision

inspection) %m %s-%d3 Head%c1 Nozzle:%d2

On-head component is brought back (pneumatic

Check the placement point and the nozzle for dirt.

1438 inspection) %m %s-%d3 Head%c1 Nozzle:%d2 %d7 >

Check that the nozzle is not choked. Check the air

offset. X:%d1 Y:%d2 Alarm:%d3 T:%d4 Alarm:%d8 range. Check the parameter setting.

1479

Dispense Nozzle Offset OK Head%c1 Angle:%d2 X:%d3

Y:%d4 T:%d5 The number of adjustments:%d8

1440 Unclamp MX-ST2.

Reached the limit of pickup or vision-process error

Unclamp MX-ST2.

1441 count. Feeder Skip %m %s-%d3 Head%c1 Nozzle:%d2

Step:%d5 Offset:%d6

Other feeder(s) will be used. The feeder will be

skipped from now on.

1442

Nozzle is detected on Head%c1. Does not agree with

inf. on Head-Nozzle Setup.

Nozzle change by hand is prohibited. Check if the tip

of the head is clean.

Nozzle is not detected on Head%c1. Does not agree

1443

1444

with inf. on Head-Nozzle Setup.

Nozzle change by hand is prohibited.

Specified number of PCBs have been produced. Press the Cancel switch to abort.

Failed to scan the PCB code. When a placed PCB is

1445

1446

unloaded, the mounter will pause by an error.

%m mode

The PCB code is scanned. When a placed PCB is

1447 unloaded, the program will be switched to the scanned

program.

Make settings of Dot Station Dispense Check in the

1448

1449

Dispense Check Data for Head%c1 is not found.

FL detect correction is disabled.

dispense check program.

FL detect correction is disabled in the user

1450

Both the FL detect correction and the vision

correction are enabled.

Select either FL detect correction or vision

correction.

Image processing result %m %s%c8 Head%c1 X:%d2

1451

Y:%d3 T:%d4 (%d5,%d6,%d7)

Component image is taken by camera.

1452 Setup of %s starts.

1453

1454

Setup of %s ends.

%s #%d1 component is set. (Components:%d2)

Updated the initial pickup point for %s [ #%d1 (P%d2#-

1455

%d3 pallet) ].

1456 %s CFB is locked.

1457 %s CFB is released.

1458

1459

%s pallet is returned.

The system switched to the %s mode.

1460

AMF Fiducial. Code:%d1 Group:%d2 X;%d3 Y:%d4 T:%d5

( %d6 %d7) %m

AMF Placement Head%d1 Angle:%d2 X:%d3 Y:%d4 T:%d5

1461

1462

(%d6 %d7 %d8) %m

Halt of head movement during PCB arrival wait %s

1463

Resumption of head movement on completion of PCB

arrival. PCB arrival wait time: %d1.%d4 seconds %s

1464

Area detection event error.(%d1 %d2:%d5 %d3->%d4

[%d8])

Obtain log data by clicking the <LOG> button and

1465

Axis status mismatch.(X:%d1 %d2->%d3 Y:%d4 %d5-

>%d6 [%d8])

Obtain log data by clicking the <LOG> button and

1466 The sensor detected the fluid shortage on Head%c1. Replenish the head with fluid in good time.

1467 Area interlock has been detected.

Obtain log data by clicking the <LOG> button and

1468

1469

1470

Switched to MX-40 upper stocker.

Switched to MX-40 lower stocker.

Timeout in temperature control for Head%c1 Check the temperature controller.

1471

Dispensing was started without the set temperature

being reached for Head%c1. Target:%v2deg C Check the temperature controller.

1472

Current:%v3deg C

Halt of Head%c1 movement for awaiting completion of

temperature control

1473

Short of OK counts for Head%s. OK count:%p2

Average ratio:%d3% Tolerance:%d4%-%d5%

Pressure:%v6Mpa Correction coefficient:%v1 %m

Number of retrials exceeded the Max Check Count

OK count < Min OK Count. Check the nozzle, syringe,

parameters.

1474

for Head%s. OK count:%p2 Average ratio:%d3% Number of retrials exceeded the specified Max Check

Tolerance:%d4%-%d5% Pressure:%v6Mpa Correction

coefficient:%v1 %m

Count. Check the nozzle, syringe, parameters.

1475

1476

Retry/Skip is not specified. Specify whether to retry or skip.

Measure DP %s( F:%d1 X:%d2 Y:%d3 AR:%d4 LS:%d5

1477

SS:%d6 SD:%d7 T:%d8 %m )

Dispense Nozzle Offset Adjustment Head%c1

1478

Angle:%d2 X:%d3->%d4 Y:%d5->%d6 T:%d7->%d8

Error in automatic acquisition of dispense nozzle Coordinates correction values exceeded the allowable

1531 %s Hook unlock sensor ON. (Pallet-%d2) Check conditions of MXR

1532 %s Hook unlock sensor OFF. (Pallet-%d2) Check conditions of MXR

1533 %s Stocker area sensor detected a pallet. Check conditions of MXR

1480

Measure DP %s( F:%d1 X:%d2 Y:%d3 AR:%d4 LS:%d5

1481

SS:%d6 SD:%d7 T:%d8 %m )

The component %m" in step No.%d1 for repeat offset

Remain Check:%d4)"

1482

step No.%d2 will be skipped. (Head%c3

The component %m" will be skipped from the step

No.%d1 for repeat offset step No.%d2. (Head%c3)"

The component exhaustion process for %m" will be

1483 postponed from the step No.%d1 for repeat offset

step No.%d2."

1484 Paused for component exhaustion. Replenish the feeder with components to restart.

1485

Production was started with the Postpone

Component Exhaustion Process" function disabled."

To enable the Postpone Component Exhaustion

Process" function

1486

1487

Out of components (%m).

The component %m" in step No.%d1 for repeat offset

Refill the components.

1488

step No.%d2 will be postponed."

Buffer stopper error

Actuate buffer stopper in manual menu

1489

Changed to safety stop" state because %s was

(Actuator/LoadBoard).

To resume production run, close the cover and press

opened." the Servo switch.

1490

Switched to %s mode and changed to safety stop"

state."

To resume production run, close the cover and press

the Servo switch.

1491

1492

Switched to %s mode.

Switched to %s mode and changed to safety stop" To resume production run, close the cover and press

state." the Servo switch.

1493

Coordinates have been lost due to trouble in return-

to-coordinate process.

Take origin again.

1494 %c1 switch cannot be activated because %s is open. Close the cover.

1495

Job run cannot be performed because the machine is

Press the Servo switch.

in the safety stop" state."

1497

1500

%s Pallet exists on hook. (Pallet-%d2)

Message

Check MXR setting

1501

1502

%s No pallet on hook. (Pallet-%d2)

%s Pallet exists on hook whereas pallet not

Check MXR setting

programmed. (Pallet-%d2)

1503

%s No pallet on hook whereas pallet programmed.

Check MXR setting

1504

(Pallet-%d2)

%s Pallet exists in stocker. Check MXR setting

1505

1506

%s No pallet in stocker. (Pallet-%d2)

%s Pallet exists in stocker whereas pallet not

Check MXR setting

programmed. (Pallet-%d2)

1507

%s No pallet in stocker whereas pallet programmed.

Check MXR setting

(Pallet-%d2)

1508 %s Pallet No. Failure in Stocker. (Pallet-%d2) Check MXR setting

1509 %s Timeout for door lock. (Pallet-%d2) Check conditions of MXR

1510 %s Timeout for door unlock. (Pallet-%d2) Check conditions of MXR

1511 %s Timeout for hook lock. (Pallet-%d2) Check conditions of MXR

1512 %s Timeout for hook unlock. (Pallet-%d2) Check conditions of MXR

1513 %s Timeout for pallet bar open. (Pallet-%d2) Check conditions of MXR

1514 %s Timeout for pallet bar close. (Pallet-%d2) Check conditions of MXR

1515 %s Timeout for pallet side clamp ON. (Pallet-%d2) Check conditions of MXR

1516 %s Timeout for pallet side clamp OFF. (Pallet-%d2) Check conditions of MXR

1517 %s Timeout for pallet rear clamp ON. (Pallet-%d2) Check conditions of MXR

1518

1519

%s Timeout for pallet rear clamp OFF. (Pallet-%d2)

%s Timeout in Elevator Movement. (Pallet-%d2)

Check conditions of MXR

1520 %s Timeout in Hook Movement. (Pallet-%d2) Check conditions of MXR

1521

%s Timeout for Elevator Returning to Origin. (Pallet-

Check conditions of MXR

%d2)

1522 %s Timeout for Hook Returning to Origin. (Pallet-%d2) Check conditions of MXR

1523 %s Pallet advance end sensor ON. (Pallet-%d2) Check conditions of MXR

1524 %s Pallet advance end sensor OFF. (Pallet-%d2) Check conditions of MXR

1525 %s Pallet bar open sensor ON (Pallet-%d2) Check conditions of MXR

1526 %s Pallet bar open sensor OFF (Pallet-%d2) Check conditions of MXR

1527 %s Pallet bar close sensor ON (Pallet-%d2) Check conditions of MXR

1528 %s Pallet bar close sensor OFF (Pallet-%d2) Check conditions of MXR

1529 %s Hook lock sensor ON. (Pallet-%d2) Check conditions of MXR

1530 %s Hook lock sensor OFF. (Pallet-%d2) Check conditions of MXR