M20_Ope_E.pdf - 第469页

3107 Failed to image the pickup point. Row:%d1 Offset:%d2 image data. 3108 Extra time was needed to start stable Laser check. %d1msec 3109 IC component feeding device is out of components or a malfunction occurred in the…

3075

Pallet information of %s and pallet positions in stocker

are not match. The machine recovered automatically.

Check pallet positions in stocker.

3076

Head stops while waiting for completion of CTF/FTF

tray setup

3041

3042

The CTF stopped. An error occurred on the other

than the CTF while the CTF was operating.

Check the CTF.

Feeder type set at %s-%d1 and %m in pickup data do Check that feeder type input in pickup data and the

3043

not match.

Failed to perform CFB correction.

feeder type set at the specified position are the

Check that correction marks are clean.

3044

%c4 does not reach the target coordinates.

(Head%c6%s Target %d1 Pushdown Stroke %d5

3045

Feedback %d2 Tolerance %d3 %m)

Fixed nozzle is specified to Head%d1 that handles the

Cancel the fixed nozzle setting.

3046

manipulator.

Head cannot travel in XY directions because of Z axis

Check Z axis status.

error.

3047

%d2mm component pitch is not available for the

feeder %m set at %s-%d1.

Select available component pitch.

3048 Electropneumatic regulator error

Check the electropneumatic regulator and the

communication path.

3049

3050

An error occurred while dispensing.

DotStation is not registered in Pickup Data.

Create DotStation row in Pickup Data and specify

Station No.

3051

3052

DotStation is not mounted at %s-%d1. Check DotStation.

Dispense head cannot exchange nozzles. Dispense head tried to exchange nozzles.

Head%s Dispense Correction OK count:%p2 Average

3053 ratio:%d3% Tolerance:%d4%-%d5% Pressure:%v6Mpa

Correction coefficient:%v1 Retry Count:%d7 %m

Executing Dispense Correction

3054

Dispense head%s height check error, Difference:

%v1mm Tolerance:%v2mm Laser check:

3055

%v3mm,%v4mm Encoder check: %v5mm,%v6mm

Feeder pitch error. %s-%d1 %m (Skipped pickup data To restart, undo the un-skipped rows or press Reset

3056

of F3 cannot be reset during a job.)

Temperature reached target temperature. For your

safety, the machine will pause.

switch.

Clear the alarm. Then restart the job.

3057

Height offset of DP head%s is out of tolerance.

Offset:%v1mm, Tolerance:%v2 to %v3mm

Check that dispense nozzle is attached securely.

3058

Dispense recheck of Head%s OK count:%p2 Average

ratio:%d3% Allowable range:%d4%-%d5% Dispense check retry will be performed.

3059

Pressure:%v6Mpa Correction coefficient:%v1 Retry

PCB warp check point exists outside of PCB. %s

Check point %d1 Limit %d2

Check that no placement data exists outside of PCB

area.

3060

Motor alarm is detected on %c2%s when Ready switch

is turned On. (Alarm code %d1 %e)

3061

By PCB height check, measured height or calculated

correction height exceeds the tolerance. Step:%d1, Check that there is no obstacle or dirt on PCB.

3062

Offset:%d2

Failed to execute PCB warp check. Coordinates X: Check that there is no through-hole or notch at

3063

%v1mm, Y: %v2mm

Laser check results are unstable. Coordinates X:

check points.

Check that there is no obstacle or dirt on PCB.

3064

%v1mm, Y: %v2mm

Comp Pitch of Feeder %m at %s-%d1 is changed from

3065

%d2mm to %d3mm.

Auto PCB warp check is available up to 10000 rows

Select Manual.

including repeat task rows.

3066

Feeder setup is verified. Feeder setup count %d1,

Feeder count in Pickup data %d2

3067

Feeder setup count %d1, Feeder count in Pickup data

%d2

3068 Server access timeout is detected. %s-%d1 ID:%d2- Check the connection of the server.

3069

F3 feeder information %s-%d1 %m, Serial No.%d3,

Component pitch %d4mm, Internal error code %d7 %e

3070

All push-up pins are on the holder. (Registered: %d1,

3071

3072

On Holder: %d2)

%s was changed to the setup state.

%s was changed to the components supply state.

3073

3074

%s stocker cover is open.

%s servo is off.

3107 Failed to image the pickup point. Row:%d1 Offset:%d2

image data.

3108

Extra time was needed to start stable Laser check.

%d1msec

3109

IC component feeding device is out of components or

a malfunction occurred in the device.

Please check IC component feeding device.

3077

Head will start traveling after completion of CTF/FTF

tray setup

3078

The component cannot be put back to the tray for

reuse because %s is in Nonstop tray setup mode. To

Press Setup switch to allow CTF/FTF to supply

components.

3079

cancel the mode, press Setup switch.

Laser calibration is interrupted.

3080

3081

Laser calibration error occurred.

Laser tool horizontal error

Tool is not horizontally assembled. Check the

3082 Laser height scale error

assembled condition.

Re-adjust the laser head assembling. Then re-

3083 Laser height check range error

execute auto calibration.

Re-adjust the laser head assembling. Then re-

3084 Laser Z offset check error

execute auto calibration.

Re-adjust the laser head assembling. Then re-

3085

3086

Laser XY offset check error

Laser immeasurable check error

execute auto calibration.

Re-execute provisional adjustment of XY offset. Then

execute auto calibration.

Make sure no dirt or obstacles are at laser transmit

part. Then re-execute auto calibration.

3087

Cannot set the feeder at the pickup station because

the feeder pickup point height exceeds the height of

limit range. %s-%d1 %m %v2mm < %v3mm

To set the feeder at a feeder station, 'ST-F1 to 13 on

M10', or 'ST-FR24 to 36 or ST-FL1 to 13 on M20',

feeder pickup point height, sum of Pickup 'Z offset' +

Feeder 'Feed height' + Package 'Height'" must be

5mm or less. (Minus Z offset is not added.)"

To set the feeder at a pickup station, 'ST-F1 to 13 on

Cannot set the feeder because Device Max Height of

M10', or 'ST-FR24 to 36 or ST-FL1 to 13 on M20',

3088 the feeder exceeds the height of limit range. %s-%d1

sum of the device max height and the feeder height

3089

%m %v2mm < %v4mm

%s communication error

must be 5mm or less.

3090

3091

%s servo error

READY %s X,%d1,Y,%d2,Z,%d3,%d4,%d5,%d6,%d7,%d8

3092 READY %s R,%d3,%d4,%d5,%d6,%d7,%d8

Angle of Dispense nozzle exceeds tolerance. Head%d1

3093

Shift: %v2 Tolerance: %v3

Refix the Dispense nozzle.

Never set a feeder during production to prevent a

3094 A feeder is set at %s-%d1 during production.

head crash.

A feeder is removed from %s-%d1 during production. Never remove a feeder during production to prevent a

3095

(The feed button of F1 or F2 feeder was pressed.) head crash.

Comp Pitch of Feeder %m at %s-%d1 is changed from

3096

%d2mm to Default.

Comp Pitch of Feeder %m at %s-%d1 is changed from

3097

3098

Default to %d3mm.

Comp Pitch of Feeder %m at %s-%d1 is selected to

Default.

Comp Pitch of Feeder %m at %s-%d1 is selected to

3099

%d2mm.

Image process is resulted in NG because failed to

3100 acquire the acceleration and/or the speed of image

capture. %m Head%c1

3101 Failed to check Dispense nozzle length. Head%d1

The offset value in the dispense data exceeds

Check that Dispense nozzle is attached properly.

Correct the offset value in Dispense Data to be within

3102

DotStation area.

Component is placed out of PCB %m Head%c1

DotStation area.

Check PCB size, placement point, component data,

3103

Row:%d5 Offset:%d6

Placement error reaches limit count. %m Head%c1

selected nozzle, and image data.

Check PCB size, placement point, component data,

3104

Row:%d5 Offset:%d6 selected nozzle, and image data.

Shortage of disk space or cannot connect a network

3105 Cannot save a log file.

drive.

Cannot drive because version of the right and the left

3106

servo amplifiers differ. Y1-AMP:%X1 Y2-AMP:%X2

Use X and Y Servo amplifiers of version E4.001.

Check the Pickup point status and the Component

3118

The conveyor width was changed after Push up pins

were located. Located %v1mm, Current %v2mm,

Tolerance +/-%v3mm

Collect the Pushup Pins manually.

3119

Push-up pin location is the same as the last time.

The process has been skipped.

Diameter of each dispensing point of multi-nozzles

cannot be compensated to the target diameter. One

3110 dispensing diameter exceeds the maximum acceptable

diameter and another dispensing diameter falls the

Please check the target diameter of each dispensing

point.

3111

minimum acceptable diameter.

Height Check NG %m %d2th row Result:%v3

Tolerance:%v4 Head%c1 Row No.:%d5 Repeat

Check the component configuration and position.

3112

Height Check NG reached retry limit %m Head%c1

Row No.:%d5 Repeat Offset:%d6

Check the component configuration and position.

3113

The PCB on the conveyor may not be reloaded.

At the start of production, the PCB was detected at

an improper position to reload. Remove the PCB and

Remove the PCB.

Adjusted offset values of Dispense Nozzle Head:%c1

Restart the production.

3114

Angle:%d2 X:%d3 Y:%d4 T:%d5

Height of the Quick Clamp is not proper. Checked %v1 Check the Quick Clamp motion. Check that no

3115

3116

Set Height %v2

Differences of check results of Laser1 and Laser2

exceed the tolerance. 1st:%v1 2nd:%v2 Tolerance:%v3

obstacles between the Quick Clamp and the

Check the lasers installation status.

3117

The Reject Conveyor %c2-%d3 in Pickup Data No. %d6

is full or not installed.

Remove components and press the RESET button. Or

install the Reject Conveyor at the proper station.