M20_Ope_E.pdf - 第450页

1384 ANC operation error Check ANC shutter and missetting of nozzle. Contact us for ANC scanning error. 1339 Communication error in image process 1340 1341 Component lack. Setup is possible %s #%d1 Pickup points of compo…

1338 %s CFB is not set.

CFB's set sensor is not responding. Set CFB in

position.

1293 MX-20 Elevator Slow-down Stop (Pallet-%d1) Check conditions of MX-20.

1294

Manual opening of ANC is detected. Unconformity in

nozzle info. may occur. Job run cannot be continued.

Perform nozzle scanning.

1295

Cannot continue operation. Machine origin

unidentified.

Select <Edit&Teach> button, and perform Origin

Initialize again.

%s Returning to Origin. Origin Sensor Z-phase

1296

1297

Distance Error(Z:%d1 - O:%d2 = %d3 > %d4)

%s operation error (Pallet-%d2)

Check the origin sensor and Z-phase input.

Check pallet information or MXR.

Paper shortage of DotStation or DotStation position Refill paper of DotStation. Or check pickup station

1298

error occurred. No. of DotStation.

1299 Dot station motor alarm. Check for cleaning paper jam or motor problem.

1300 Standard device %c4%c1%s initialization error (%e) Error at control board/driver. Contact us.

1301

1302

Program error. Failed to initialize the task.

Program error

System error. Contact us.

1303

Drive signal is not turned On. (The cover may not be

closed properly.)

System error. Contact us.

Motor alarm at the initialization of %c4%c2%s. (alarm Turn off servomotors via Maintenance>ServoOff. Ten

1304

1305

code %d1)

Option device %c4%c1%s is not initialized properly. (%e)

minutes later, turn them on.

Error at control board/driver. Contact us.

Check the setting of IC card and communication

1306 Vision system initialization error

cable. Restart the system.

1307 Air pressure at initialization is abnormal. Check the air piping and restart the system.

1308 Command sequence error Contact us.

1309 Paused for postponed retry steps. Press <Recovery> switch and then <Start> switch.

1310 Improper component feeding %s #%d1 Head%c2 Stop operation and check feeding conditions.

1311 No available feeder %s #%d1 Head%c2 Stop operation and check for presence of feeder.

1312

1313

Feeder error Head%c1

Improper component feeding %s #%d1

Out of component or no component at pickup point.

Stop running and check the feeding conditions.

1314 Job run is paused.

Set up the mounter and resume job run by pressing

<Recovery> and <Start>.

1315

Component is detected on the nozzle in comp.

Remain Check.

Check the pickup/placement and take proper

measures in the Edit & Teach mode.

%m PCB code mismatch was detected. Auto program

1316

1317

change was performed.

%m PCB code mismatch was detected.

Auto program change was performed.

PCB code mismatch was detected.

Nozzles on heads and Nozzle Information do not If the machine does not recognize nozzle IDs properly,

1318

1319

match.

No program step to execute.

Check the program setting (skip assignment, etc.).

1320

Reached the limit of vision-process retry count (%m

%s-%d3 Head%c1 Nozzle No.%d2 Step:%d5

Check the image library data and illumination setting.

1321

Reached the limit of pickup retry count (%m %s-%d3

Head%c1 Nozzle No.%d2 Step:%d5 Offset:%d6)

Check the pickup coordinates and nozzle choice.

1322

Reached the limit of feeder retry count (%m %s-%d3

Head%c1 Nozzle No.%d2 Step:%d5 Offset:%d6)

Check the component feeding conditions.

1323

Out of component (%m %s-%d3 Head%c1 Nozzle

No.%d2 Step:%d5 Offset:%d6)

After replenishing components, update the component

count setting.

1324

Reached the limit of choke-pressure retry count

(Head%c1 Nozzle No.%d2 Step:%d5 Offset:%d6)

Check the air pressure, air filter, and nozzle data.

Check that the component feeder is mounted. Check

1325

Usable feeder is not mounted. Head%c1, Nozzle

No.%d2, Step:%d5, Offset:%d6

that the feeder is mounted on the head reachable

station.

Reached the limit of coplanarity retry count (%m %s- Check the component's image code and coplanarity

1326

1327

%d3 Head%c1 Nozzle No.%d2 Step:%d5 Offset:%d6)

Timeout in coplanarity check

data.

Check the wiring of the LIM unit.

Check the power to the LIM unit. Check the wiring of

1328 Power to the LIM unit is off.

the LIM unit.

1329 LIM unit is in the local mode. Switch the LIM unit's mode to the host mode.

1330

1331

Out of component. %s #%d1

Out of component. %s #%d1 (P%d2#-%d3 pallet)

Replenish components.

1332 Components are running out. %s #%d1 rest %d2 pcs.

Components are used down to

Program>PickupData>ShortageAlarm setting.

Components are running out. %s #%d1 (P%d2#-%d3 Components are used down to

1333

pallet) rest %d4 pcs. Program>PickupData>ShortageAlarm setting.

1334 Failed to lock CFB %s. Check CFB lock mechanism.

1335 Failed to unlock CFB %s. Check CFB lock mechanism.

1336

1337

Setup ready error

Setup complete error

Check CFB lock mechanism.

1384 ANC operation error

Check ANC shutter and missetting of nozzle. Contact

us for ANC scanning error.

1339 Communication error in image process

1340

1341

Component lack. Setup is possible %s #%d1

Pickup points of component lack are displayed.

Replenish components.

Vision process sequence error. Execute system

1342

recovery.

Check Vision processing unit or Cables for error.

1343 Failed to clamp MX-ST2. Failed to clamp MX-ST2.

1344 Failed to unclamp MX-ST2. Failed to unclamp MX-ST2.

1345 %s pallet setting error (Pallet-%d2) Check pallet information or MXR.

1346

1347

%s origin acquisition error (Pallet-%d2)

Cannot supply components from %s.

Check conditions of MXR.

Check the feeder.

The feeder is specified as unavailable feeder. %s Clear the Feeder Skip state for concerned pickup

1348

1349

#%d1

AMF measurement ends.

point(s).

1350 Setup error

This error is caused by effect of other errors. Check

the other error messages near around.

1351

Retry step postpone table is full. Execute normal

retry process.

Retry step postpone table is full. Execute normal

retry process.

MAP measurement ends. Press Start SW to convey

1352 MAP measurement ends.

out the board.

1353

1354

Axis movements are unstable.

There are no usable pickup points because the

1355 machine is in the changeover state. (%m %s-%d3

Head%c1 Nozzle No.%d2 Step:%d5 Offset:%d6)

End the changeover state.

1356 Reject conveyor on %s %d1 is almost out of space.

There are no usable pickup points because Feeder

Components on Reject conveyor are almost full.

(Warning!)

1357 Skip is/are specified. (%m %s-%d3 Head%c1 Nozzle

Clear the Feeder Skip state for concerned pickup

1358

No.%d2 Step:%d5 Offset:%d6)

Controller error

point(s).

System is not operating properly. Contact us.

Check the code entry equipment for settings and

1359 PCB code entry error connections. To continue the job run, check the PCB

code and select the program.

1360 %s Motor alarm

Execute Maintenance>ServoOff. Ten minutes later,

turn on <Servo> switch.

Coordinates exceeded the setting of

1361 %s position exceeded the limit. SystemParameter>WorkRange or

SystemParameter>Axis>TravelDist.

1362 %s detected EL(+). Overrun. Take origin again.

1363 %s detected EL(-). Overrun. Take origin again.

1364 Origin of %s is not taken. Check Origin menu.

1365

1366

%s error

Error occurs at %s.

Remove error.

1367 %m PCB code is not defined in the Plan.

Define the PCB code in the Plan and select the

program.

Fiducial correction was not performed. Change the

1368 Fiducial error (4point)

mark location.

1369

1370

Timeout in %s operation.

ANC slide channel operates improperly.

Check cylinders, motors, and sensors.

Check cylinders and sensors.

This nozzle station is not for removing nozzles from

1371 The nozzle cannot be removed from the head.

heads.

1372 Error occurs in image processing. Check image process system and communication

1373 Device cannot be initialized. Contact us.

1374

1375

Error in opening PS-BC shutter. %s (%d1)

Error in closing PS-BC shutter. %s (%d1)

Check the shutter mechanism of the bulk feeder.

1376 Main clamp is abnormal.

Check support pin for crash. Check adjust plate for

foreign matters.

Check PCB stopper for normal operation st Manual

1377 PCB stopper is abnormal.

menu.

1378 Rear clamp is abnormal. Check rear clamp for normal operation.

1379

1380

Side clamp is abnormal.

ANC shutter is abnormal.

Check side clamp.

Check ANC shutter.

Computing error for correction. Save Log file and

1381 Fiducial error (calculation)

1382

1383

Conveyor error

Disconnect the cable and air tube for the CFB.

Check conveyor transfer belts and motors.

%d8 Step:%d5 Offset:%d6

pressure.

1439 Clamp MX-ST2. Clamp MX-ST2.

Check ANC shutter and missetting of nozzle. Contact

1385 ANC scanning error

us for ANC scanning error.

1386 MX-40 pallet setting error Check pallet information or MX-40.

1387 MX-40 origin acquisition error Check MX-40.

1388 MX-40 shuttle contacts conveyor rail. Check conveyor rail position.

1389 Feeder cannot operate. Check feeder for misfeeding.

1390 Signal output operation error System is abnormal. Contact us.

1391

1392

PS-32A tape-peeling error %s (%d1)

PS-32A re-positioning error %s (%d1)

Check Feeder Setting or check the feeder.

PS-32A sequence clear command control error %s

1393

(%d1)

Check Feeder Setting or check the feeder.

1394 MX-20 pallet setting error (Pallet-%d1) Check pallet information or MX-20.

1395 MX-20 origin acquisition error (Pallet-%d1) Check MX-20.

1396 MX-F20 shuttle contacts conveyor rail. Check conveyor rail position.

1397 Failed to retract MX-40 pallet Check MX-40 setting and conditions of MX-40B

1398 Failed to retract MX-20 pallet (Pallet-%d1) Check MX-20 setting and conditions of MX-20F

1399 Failed to retract %s pallet (Pallet-%d2) Check pallet information or MXR.

1400 %m

1401 %s is open.

1402 %s is pressed.

1403 Origin detection starts.

1404 Sensor of the safety guard responded.

1405 Origin has been detected.

1406 Waiting for Board arrival at %s. Waiting for Board arrival.

1407 Board starts to enter at %s. Just started Board transfer in.

1408 Board has arrived at %s. Completed Board transfer in.

1409 IN sensor detects board.

1410 Buffer sensor detects board.

1411 Arrival sensor detects board.

1412 OUT sensor detects board.

1413 Board clamp starts.

1414 Board clamp ends.

1415 Board unclamp starts.

1416 Board unclamp ends.

1417 Board is ready to be conveyed out at %s. Board is ready to be conveyed out.

1418

1419

Board starts to be conveyed out at %s.

Board has been away from %s.

Just started Board transfer out.

Completed Board transfer out.

1420

Canceled the job with the multiple-pickup cycle

halfway done.

When production is cancelled without completing

Cannot handle the multiple-pickup cycle by normal

resume procedure.

1421 postponed components, restart the production by

selecting Continue"."

Postponed components cannot be placed by selecting

Start from the selected row.""

1422 Canceled the job with components being picked up.

Remove the picked up components to resume

production.

No program step to execute. Pass the PCB through. No program step to execute due to component skip

1423

%s or etc. Check components.

1424 Waiting for Board arrival at %s. Waiting for Board arrival.

1425

1426

Board starts to enter at %s.

Board has arrived at %s.

Just started Board transfer in.

Completed Board transfer in.

1427

Pickup error %m %s-%d3 Head%c1 Nozzle No.%d2

%d7 < %d8 Step:%d5 Offset:%d6

Check status of Head, Component, and Pickup point.

1428

Pickup error (no countermeasure) %m %s-%d3

Head%c1 Nozzle No.%d2 %d7 < %d8 Step:%d5

Choke pressure error Head%c1 Nozzle No.%d2 %d7

1429

> %d8

Nozzle is choked.

1430 Feeder indexing starts.

1431 %s can be set up. Replenish components.

1432 Feeder indexing ends.

1433 %s waits to be unloaded.

1434

1435

Unloading PCB from %s starts.

Unloading PCB from %s is complete.

1436

Coplanarity measurement error %m %s-%d3 Head%c1

Nozzle No.%d2 Step:%d5 Offset:%d6

1437

On-head component is brought back (vision

inspection) %m %s-%d3 Head%c1 Nozzle:%d2

On-head component is brought back (pneumatic

Check the placement point and the nozzle for dirt.

1438 inspection) %m %s-%d3 Head%c1 Nozzle:%d2 %d7 >

Check that the nozzle is not choked. Check the air