SME_Jig_User_Guide(Eng_Ver1).pdf - 第94页
6-2 User's Guide For Tape Fe eder Calibration Jig Camera screen is not shown. Communication is disconnected due to a problem with the software. Exit and restart the calibration jig program. Defective cont act of the…
6-1
TroubleShooting
Chapter6. TroubleShooting
6.1. Problems and Measures
Describes problems that may occur when using a calibration jig for an SME feeder and
measures against them.
Problem Possible Cause Measures
Power is
not turned
on.
The power switch of the calibration
jig is turned off.
Turn on the power switch of
the calibration jig.
The switch of the multi-tab
supplying power to the calibration
jig is turned off.
Turn on the multi-tab switch.
The 220V power cable is defective. Replace the 220V power
cable.
The SMP is defective. Contact our C/S and replace
the SMP.
When the power supply fuse of the
calibration jig is cut off
Replace the power supply
fuse.
Communic
ation is not
available.
Communication is disconnected
due to a problem with the software.
Exit and restart the calibration
jig program.
Defective contact of the USB25PIN
cable.
Replace the USB25PIN cable.
While running the calibration jig
program in the PC, conflict of
programs occurred.
Exit and restart the calibration
jig program.
Reboot the PC.
If the problem is not solved,
reinstall the calibration jig
program.
A problem occurred to the wiring
from the CAN board to the
USB2USB holder.
Contact our designated C/S
(STS) or our overseas agent
and replace the wiring.
A problem occurred to the CAN
board.
Contact our designated C/S
(STS) or our overseas agent
and replace the CAN board.
6-2
User's Guide For Tape Feeder Calibration Jig
Camera
screen is
not shown.
Communication is disconnected
due to a problem with the software.
Exit and restart the calibration
jig program.
Defective contact of the USB25PIN
cable.
Replace the USB25PIN cable.
While running the calibration jig
program in the PC, conflict of
programs occurred.
Reboot the PC.
A problem occurred to the camera
driver installed in the PC.
Delete the camera driver in the
PC and reinstall the driver.
A USB hub is installed at the USB
2.0 port.
Install the USB hub at the USB
3.0 port.
Devices other than reader, CAN
communication cable and camera
are used at the USB hub.
Stop using an external device.
A problem occurred to the camera. Contact our designated C/S
(STS) or our overseas agent
and replace the camera.
The
calibration
jig program
is not
executed.
The PC OS is Windows 7 or below. Use a program above OS
Windows 7.
The PC OS is Windows 7 or above,
but it is 64 bit.
Use the program with
Windows 7 and 32 bit.
The
calibration
jig program
was shut
down.
Software bug occurred or USB
device conflict occurred.
Rerun the calibration jig
program.
Problem Possible Cause Measures
6-3
TroubleShooting
When
rerunning
the
calibration
jig program
after it was
shut down,
camera
and CAN
communic
ation
failure
occurred.
USB device conflict occurred. Remove the USB from the PC
and rerun the calibration jig
program.
The
calibration
jig program
execution
screen is
cut.
The display resolution is less than
1920x1080.
Set the display resolution to
1920x1080 and higher.
The origin
of the
master
feeder is
not shown.
The master feeder is not clamped. Move the master feeder lever
up and clamp it.
The XY positions are not correct. Adjust the stage XY axes so
that the origin of the master
feeder can be seen.
A clearance occurred between
master feeder and feeder base.
Remove the foreign materials
from the feeder base.
The origin
of the
master
feeder
looks
blurred.
The master feeder is not clamped. Move the master feeder lever
up and clamp it.
The Z position is not correct. Adjust the stage Z-axis.
A clearance occurred between
master feeder and feeder base.
Remove the foreign materials
from the feeder base.
When
setting the
origin of
the master
feeder, its
position is
not correct.
The threshold value is not
appropriate.
Adjust the threshold value so
that the feeder origin can be
seen clearly.
Problem Possible Cause Measures