SME_Jig_User_Guide(Eng_Ver1).pdf - 第95页

6-3 TroubleShooting When rerunning the calibra t ion ji g pro gr am af ter it was shut down, camera and CAN communic ation failure occurred. USB device conflict occurred. Remove the USB from the PC and rerun the calibrat…

100%1 / 110
6-2
User's Guide For Tape Feeder Calibration Jig
Camera
screen is
not shown.
Communication is disconnected
due to a problem with the software.
Exit and restart the calibration
jig program.
Defective contact of the USB25PIN
cable.
Replace the USB25PIN cable.
While running the calibration jig
program in the PC, conflict of
programs occurred.
Reboot the PC.
A problem occurred to the camera
driver installed in the PC.
Delete the camera driver in the
PC and reinstall the driver.
A USB hub is installed at the USB
2.0 port.
Install the USB hub at the USB
3.0 port.
Devices other than reader, CAN
communication cable and camera
are used at the USB hub.
Stop using an external device.
A problem occurred to the camera. Contact our designated C/S
(STS) or our overseas agent
and replace the camera.
The
calibration
jig program
is not
executed.
The PC OS is Windows 7 or below. Use a program above OS
Windows 7.
The PC OS is Windows 7 or above,
but it is 64 bit.
Use the program with
Windows 7 and 32 bit.
The
calibration
jig program
was shut
down.
Software bug occurred or USB
device conflict occurred.
Rerun the calibration jig
program.
Problem Possible Cause Measures
6-3
TroubleShooting
When
rerunning
the
calibration
jig program
after it was
shut down,
camera
and CAN
communic
ation
failure
occurred.
USB device conflict occurred. Remove the USB from the PC
and rerun the calibration jig
program.
The
calibration
jig program
execution
screen is
cut.
The display resolution is less than
1920x1080.
Set the display resolution to
1920x1080 and higher.
The origin
of the
master
feeder is
not shown.
The master feeder is not clamped. Move the master feeder lever
up and clamp it.
The XY positions are not correct. Adjust the stage XY axes so
that the origin of the master
feeder can be seen.
A clearance occurred between
master feeder and feeder base.
Remove the foreign materials
from the feeder base.
The origin
of the
master
feeder
looks
blurred.
The master feeder is not clamped. Move the master feeder lever
up and clamp it.
The Z position is not correct. Adjust the stage Z-axis.
A clearance occurred between
master feeder and feeder base.
Remove the foreign materials
from the feeder base.
When
setting the
origin of
the master
feeder, its
position is
not correct.
The threshold value is not
appropriate.
Adjust the threshold value so
that the feeder origin can be
seen clearly.
Problem Possible Cause Measures
6-4
User's Guide For Tape Feeder Calibration Jig
The size of
the master
tape origin
is different
from that of
the
recognition
line when
grabbing it.
The vision resolution value is not
appropriate.
Adjust the resolution value and
perform setup so that the origin
size will be the same as the
recognition line size.
When
inputting a
serial
number
through
barcode
scanning, it
is different
from the
saved
value.
When inputting a serial number, an
incorrect value was inputted
manually.
Have the barcode recognized
using the barcode scanner.
Failed to recognize the serial
number properly due to a
communication defect.
Refer to the problem,
[Communication not available].
After replacing the main board, the
serial number is not saved in the
main board.
Save the serial number in the
main board in the Repair
menu.
When
inspecting
the part
supply
accuracy,
back-
feeding is
not
performed.
The firmware version of the tape
feeder is 1.26 and below.
Update the firmware version of
the tape feeder to version 1.26
and above.
When
inspecting
the part
supply
accuracy,
the <X
NG>
occurred.
Foreign material is jammed in the
feeder base slot when setting the
origin of the master feeder.
After removing the foreign
material, set the origin again.
The master feeder is not clamped
when setting the origin.
Clamp the master feeder and
set the origin.
The tape feeder is bent. Adjust the X eccentric pin and
inspect the supply accuracy
again.
The X position was set incorrectly
while performing mapping.
Adjust the X eccentric pin and
inspect the supply accuracy
again.
Problem Possible Cause Measures