4OM-1003-007.pdf - 第182页

Check Code Display Section A Display Section B 0301 20 Operator ’s Error Check the feeder . (the feeder checker) 030121 Operator ’ s Error Remove the P .C.B. at the inlet of input buf fer cnvr . 030122 Operator ’s Error …

1.2.2 List of Check Messages

Table 4B1

Check Code Display Section A Display Section B

010101 Emergency Stop Turn on the [POWER ON] button.

010201 Air Pressure Drop Increase air pressure and press the [POWER ON] button to power

up the machine.

010301 Feeder Axis Central Close the feeder safety guard and press the [POWER ON] button

Safety Guard to power up the machine.

010401 Front Side Safety Close the safety door and press the [POWER ON] button to power

Door up the machine.

010501 Circuit Protector Circuit protector is active in the machine.

010601 Control Power

Source

030101 Operator’s Error Set operation mode to "placement".

030102 Operator’s Error Please select the available menu.

030103 Operator’s Error Input registered test ID.

030104 Operator’s Error Select correct combination of camera and lighting mode.

030105 Operator’s Error Selected available carriage.

030106 Operator’s Error Cancel the component shortage designated position stop func-

tion.

030107 Operator’s Error Recovery mode is not available while grouped component func-

tion is implemented.

030108 Operator’s Error Set "ENABLE" for destination alternate feeder.

030109 Operator’s Error Machine is in "PAUSE" mode.

03010a Operator’s Error Stop the input cnvr. (+) movement in manual mode.

03010b Operator’s Error Stop the input cnvr. (-) movement in manual mode.

03010c Operator’s Error Input correct data for manual axis operation.

03010d Operator’s Error Please input correct nozzle type data.

03010e Operator’s Error Input non-defective P.C.B. (O-NO.)

03010f Operator’s Error Wait until data communication with external device is completed.

030110 Operator’s Error P.C.B.’s were at inlet and outlet of input buffer cnvr.

030111 Operator’s Error P.C.B.’s were at inlet and outlet of input cnvr.

030112 Operator’s Error P.C.B. on Inp. Cnvr. was not able to move to its transfer action.

030113 Operator’s Error P.C.B. stop movement in manual mode.

030114 Operator’s Error Please input the test ID.

030115 Operator’s Error Please cancel "set up" mode as closing a safe cover.

030116 Operator’s Error P.C.B.’s were at inlet and outlet of output cnvr.

030117 Operator’s Error Remove the P.C.B. at the inlet of output cnvr.

030118 Operator’s Error Remove P.C.B. on the L conveyor.

030119 Operator’s Error Remove P.C.B. on the R conveyor.

03011a Operator’s Error Remove P.C.B. on the X/Y table.

03011b Operator’s Error Cannot start in CVS start protection mode.

03011c Operator’s Error Remove P.C.B. on the conveyor.

03011d Operator’s Error Cancel the start protect mode.

03011e Operator’s Error Out of range P.C.B. is exist on the conveyor.

(lot management production)

03011f Operator’s Error Not released p-out mode.

0305-001 2-4 AIL01ETRP

1.2 "CHECK" Windows

Check Code Display Section A Display Section B

030120 Operator’s Error Check the feeder. (the feeder checker)

030121 Operator’s Error Remove the P.C.B. at the inlet of input buffer cnvr.

030122 Operator’s Error Check the program name of bar code.

(the P.C.B. is on the input cnvr.)

030123 Operator’s Error It isn’t practicable with "set up" mode.

030124 Operator’s Error It isn’t practicable with "P.C.B. clamp valve" menu select.

030125 Operator’s Error Please read of barcode label on the P.C.B.

030126 Operator’s Error The fdr. was not recorded SIF data exists.

Please record by mnl. operation.

030128 Operator’s Error The fdr. was not recorded SIF data exists.

Please record by mnl. operation.

03012a Operator’s Error Remove the P.C.B. at the input cnvr.

03012b Operator’s Error Cannot start by external start protection.

03012c Operator’s Error Please change enable mode into disable mode.

(serial out mode)

03012d Operator’s Error Remove the P.C.B. at the input cnvr.

(the P.C.B. not enable B.B.R. info.)

03012e Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode (conveyor).

03012f Operator’s Error Remove the P.C.B. at middle position of input buffer cnvr.

030130 Operator’s Error Cannot start by external start protection. (R1)

030131 Operator’s Error Cannot start by external start protection. (R2)

030132 Operator’s Error Cannot start by Machine is already in "running" mode.

030133 Operator’s Error Enable SW is busy status.

030134 Operator’s Error Cannot start by Machine is already in "running" unit.

030135 Operator’s Error Cannot start by Machine is not in "STOP" mode.

030136 Operator’s Error Cannot start by Machine is not in "STOP" or "PAUSE" mode.

030137 Operator’s Error Remove the P.C.B. at inside the L1 cnvr.

030138 Operator’s Error Remove the P.C.B. at outside the L1 cnvr.

030139 Operator’s Error Remove the P.C.B. at inside the L2 cnvr.

03013a Operator’s Error Remove the P.C.B. at outside the L2 cnvr.

03013b Operator’s Error Remove the P.C.B. at inside the R1 cnvr.

03013c Operator’s Error Remove the P.C.B. at outside the R1 cnvr.

03013d Operator’s Error Remove the P.C.B. at inside the R2 cnvr.

03013e Operator’s Error Remove the P.C.B. at outside the R2 cnvr.

03013f Operator’s Error Use nozzles are insufficient.

Please cancel a bypass or set a nozzle.

030140 Operator’s Error Press [EMER STOP] switch and open the F-axis safety door and

clean the linear encoder scale-tape.

030141 Operator’s Error Press [EMER STOP] switch and open the F-axis safety door and

refresh the grease.

0511-002 2-5 AIL01ETRP

1.2 "CHECK" Windows

0511-002 2-6 AIL01ETRP

1.2 "CHECK" Windows

Check Code

Display Section A Display Section B

030142 Operator’s Error [EMER STOP] switch and Open the F-axis safety door and Clean

the linear slide guide.

030143 Operator’s Error A pause conveyance function is effective. Please operate it after

setting up a function invalid.

030144 Operator’s Error Not found valid sequence. Attach a component to a nozzle.

030145 Operator’s Error Lock operation panel.

030146 Operator’s Error Please read of barcode label on the P.C.B.(front cnvr.)

030147 Operator’s Error Please read of barcode label on the P.C.B.(input cnvr.)

030148 Operator’s Error Please read of barcode label on the P.C.B.(input buffer cnvr.)

030149 Operator’s Error Please the [Jig Dtch (X/Y MVT)] menu select.

03014a Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode(barcode mode).

03014b Operator’s Error Lock front operation panel.

03014c Operator’s Error Lock back operation panel.

03014d Operator’s Error This operation is possible only front operation panel.

03014e Operator’s Error This operation is possible only back operation panel

03014f Operator’s Error Remove the P.C.B. at input machine cnvr.

030150 Operator’s Error Remove the P.C.B. at output machine cnvr.

030151 Operator’s Error [STOP] switch has been pressed.

030157 Operator’s Error Remove the P.C.B. at the output cnvr.

030158 Operator’s Error Remove P.C.B. on the X/Y table at Left side or Right side position.

030159 Operator’s Error Please make the priority alternate unit preparation complete.

(Only the priority unit use mode. )

030160 Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode (communication/

barcode mode). Change pattern program single U-N pattern.

030201 Out Of Specified Rotate the rotary turret to designated angle.

Rotary Turret Angle

030301 Head Bypass Cancel bypass operation of selected head or do not use the head.

030302 Head Bypass The specified head is bypassed.

030303 Head Bypass The specified nozzle is bypassed.

030304 Specify the nozzle The specified nozzle type is not exist.

type