4OM-1003-007.pdf - 第231页

Error ID Item Description 04060c Comp. Place. (Z) Axis Servo off time out Servo Error 04060d Comp. Place. (Z) Axis Servo power off Servo Error (Cause 1) Self-Diagnostics Error Message (Remedy 1) Zero all axes and re-star…

100%1 / 409
Error ID Item Description
040601 Comp. Place. (Z) Axis Emergency stop
Servo Error
040602 Comp. Place. (Z) Axis Encoder error
Servo Error [Shutdown touch sw key and mainbreaker sw off.]
040603 Comp. Place. (Z) Axis Mechatrolink cut error
Servo Error [Shutdown touch sw key and mainbreaker sw off.]
040604 Comp. Place. (Z) Axis Location timeout
Servo Error
040605 Comp. Place. (Z) Axis Position error pulse overflow error
Servo Error
040606 Comp. Place. (Z) Axis Software limit (-)
Servo Error
040607 Comp. Place. (Z) Axis Software limit (+)
Servo Error
040608 Comp. Place. (Z) Axis Illegal parameter
Servo Error
040609 Comp. Place. (Z) Axis System error
Servo Error
04060a Comp. Place. (Z) Axis Illegal command
Servo Error
04060b Comp. Place. (Z) Axis Servo on time out
Servo Error
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0511-002 2-50 AIL01ETRP
3.3 Error IDs and Remedial Procedures
Error ID Item Description
04060c Comp. Place. (Z) Axis Servo off time out
Servo Error
04060d Comp. Place. (Z) Axis Servo power off
Servo Error
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
040701 Comp. Place. (Z) Axis Interlock Movement cannot take place until the index angle is adjusted.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
040801 Comp. Place. (Z) Axis Communication error was detected.
Communication
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0511-002 2-51 AIL01ETRP
3.3 Error IDs and Remedial Procedures
(05 Table X)
Error ID Item Description
050101 Table-X Axis Origin Encoder origin was not detected.
(Cause 1) The encoder section of the motor may be defective or the encoder cable may be
broken.
(Remedy 1) Turn off the power and check for looseness of the connector section for the signal
cable.
If the error is not canceled yet after this check operation, the broken signal cable
or the motor may be defective. Consult our service personnel for the remedy.
050102 Table-X Axis Origin Origin sensor (slide) was not detected.
(Cause 1) The sensor may be defective or the cable may be broken.
(Remedy 1) Press the [RETURN] button to cancel the error display and then the [ALL] button
entitled "ZERO".
If the error cannot be canceled after the zeroing operation, it is required to re-
place the sensor or the sensor cable with a new one. Consult our service person-
nel for details.
050103 Table-X Axis Origin Origin sensor (slide) and Limit error has been detected.
050104 Table-X Axis Origin Feedback value is indefinite.
050105 Table-X Axis Origin The component pick-up (z) axis is not at origin.
050201 Table-X Axis Timing Task has not been completed unable to continue.
050301 Table-X Axis Data The driver data was detected outside of the possible range.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service per
sonnel for the remedy.
0511-002 2-52 AIL01ETRP
3.3 Error IDs and Remedial Procedures