4OM-1003-007.pdf - 第183页

051 1-002 2-6 AIL01ETRP 1.2 "CHECK" Windows Check Code Display Section A Display Section B 030142 Operator ’s Error [EMER ST OP] switch and Open the F-axis safety door and Clean the linear slide guide. 030143 O…

100%1 / 409
Check Code Display Section A Display Section B
030120 Operator’s Error Check the feeder. (the feeder checker)
030121 Operator’s Error Remove the P.C.B. at the inlet of input buffer cnvr.
030122 Operator’s Error Check the program name of bar code.
(the P.C.B. is on the input cnvr.)
030123 Operator’s Error It isn’t practicable with "set up" mode.
030124 Operator’s Error It isn’t practicable with "P.C.B. clamp valve" menu select.
030125 Operator’s Error Please read of barcode label on the P.C.B.
030126 Operator’s Error The fdr. was not recorded SIF data exists.
Please record by mnl. operation.
030128 Operator’s Error The fdr. was not recorded SIF data exists.
Please record by mnl. operation.
03012a Operator’s Error Remove the P.C.B. at the input cnvr.
03012b Operator’s Error Cannot start by external start protection.
03012c Operator’s Error Please change enable mode into disable mode.
(serial out mode)
03012d Operator’s Error Remove the P.C.B. at the input cnvr.
(the P.C.B. not enable B.B.R. info.)
03012e Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode (conveyor).
03012f Operator’s Error Remove the P.C.B. at middle position of input buffer cnvr.
030130 Operator’s Error Cannot start by external start protection. (R1)
030131 Operator’s Error Cannot start by external start protection. (R2)
030132 Operator’s Error Cannot start by Machine is already in "running" mode.
030133 Operator’s Error Enable SW is busy status.
030134 Operator’s Error Cannot start by Machine is already in "running" unit.
030135 Operator’s Error Cannot start by Machine is not in "STOP" mode.
030136 Operator’s Error Cannot start by Machine is not in "STOP" or "PAUSE" mode.
030137 Operator’s Error Remove the P.C.B. at inside the L1 cnvr.
030138 Operator’s Error Remove the P.C.B. at outside the L1 cnvr.
030139 Operator’s Error Remove the P.C.B. at inside the L2 cnvr.
03013a Operator’s Error Remove the P.C.B. at outside the L2 cnvr.
03013b Operator’s Error Remove the P.C.B. at inside the R1 cnvr.
03013c Operator’s Error Remove the P.C.B. at outside the R1 cnvr.
03013d Operator’s Error Remove the P.C.B. at inside the R2 cnvr.
03013e Operator’s Error Remove the P.C.B. at outside the R2 cnvr.
03013f Operator’s Error Use nozzles are insufficient.
Please cancel a bypass or set a nozzle.
030140 Operator’s Error Press [EMER STOP] switch and open the F-axis safety door and
clean the linear encoder scale-tape.
030141 Operator’s Error Press [EMER STOP] switch and open the F-axis safety door and
refresh the grease.
0511-002 2-5 AIL01ETRP
1.2 "CHECK" Windows
0511-002 2-6 AIL01ETRP
1.2 "CHECK" Windows
Check Code
Display Section A Display Section B
030142 Operator’s Error [EMER STOP] switch and Open the F-axis safety door and Clean
the linear slide guide.
030143 Operator’s Error A pause conveyance function is effective. Please operate it after
setting up a function invalid.
030144 Operator’s Error Not found valid sequence. Attach a component to a nozzle.
030145 Operator’s Error Lock operation panel.
030146 Operator’s Error Please read of barcode label on the P.C.B.(front cnvr.)
030147 Operator’s Error Please read of barcode label on the P.C.B.(input cnvr.)
030148 Operator’s Error Please read of barcode label on the P.C.B.(input buffer cnvr.)
030149 Operator’s Error Please the [Jig Dtch (X/Y MVT)] menu select.
03014a Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode(barcode mode).
03014b Operator’s Error Lock front operation panel.
03014c Operator’s Error Lock back operation panel.
03014d Operator’s Error This operation is possible only front operation panel.
03014e Operator’s Error This operation is possible only back operation panel
.
03014f Operator’s Error Remove the P.C.B. at input machine cnvr.
030150 Operator’s Error Remove the P.C.B. at output machine cnvr.
030151 Operator’s Error [STOP] switch has been pressed.
030157 Operator’s Error Remove the P.C.B. at the output cnvr.
030158 Operator’s Error Remove P.C.B. on the X/Y table at Left side or Right side position.
030159 Operator’s Error Please make the priority alternate unit preparation complete.
(Only the priority unit use mode. )
030160 Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode (communication/
barcode mode). Change pattern program single U-N pattern.
030201 Out Of Specified Rotate the rotary turret to designated angle.
Rotary Turret Angle
030301 Head Bypass Cancel bypass operation of selected head or do not use the head.
030302 Head Bypass The specified head is bypassed.
030303 Head Bypass The specified nozzle is bypassed.
030304 Specify the nozzle The specified nozzle type is not exist.
type
Check Code Display Section A Display Section B
030401 Operation Please input barcode data by manual input screen.
Requirement
030402 Operation Please check the operation in "pass" mode.
Requirement
030403 Operation X/Y chute P.C.B. detection is one side mode.
Requirement
030404 Operation Please exit P.E.C. manual adjustment mode.
Requirement (Click right and left button)
030405 Operation Please wait for a while.
Requirement (Now Machine is initializing.)
030406 Operation Nozzle level mismatch with component thickness (t). Collect
Requirement component and attach one again.
030407 Operation Recognition fail. Check data and component position.
Requirement
030408 Operation The current program changed. Please perform setup operation.
Requirement
030409 Operation Please check final mount step condition for eye adjustment.
Requirement This mount position was detected outside of the possible
range.(PEC position)
030410 Operation This teach point was detected outside of the possible range.
Requirement
030411 Operation This origin point was detected outside of the possible range.
Requirement (PEC position)
030412 Operation This destinate step was detected outside of the possible range.
Requirement (PEC position)
050101 No Current Select the current program.
050102 No Current Incorrect data found within internal current program. Please retry
program change.
050201 Setup Check Set up X/Y chute width.
050202 Setup Check Set up L conveyor width.
050203 Setup Check Set up R conveyor width.
050204 Setup Check Set up conveyor width.
050205 Setup Check Move the X/Y chute up.
050206 Setup Check Set up PCB support pins up/down.
050207 Setup Check Set up PCB locate lever.
050208 Setup Check Please input transfer stroke data.
050209 Setup Check Please input Zero Position.
05020a Setup Check Please input PCB locate lever size.
05020b Setup Check Set up X/Y chute width for Y-clamp action.
05020c Setup Check Please Transfer and Set P.C.B. on the X/Y table. (X/Y table on
P.C.B. is non clamp condition.)
0511-002 2-7 AIL01ETRP
1.2 "CHECK" Windows