4OM-1003-007.pdf - 第194页
Check Code Display Section A Display Section B 800D08 Maintenance Keep the machine condition.(maintenance cycle time : Upkeep- Warning Checkup/Nozzle) 800D09 Maintenance Keep the machine condition.(maintenance cycle time…
Check Code Display Section A Display Section B
800901 Alarm For The tape end was detected.
Shortage of Comp.
800902 Alarm For Few components to feed.
Shortage of Comp.
(Contents) Self-Diagnostics Error Message
(Description) The automatic operation will stop soon due to component shortage.
Prepare for component replenishment.
800A01 Product information Finished product interval :
800A02 Product information Auto run interval :
800A03 Product information Nozzle usage interval :
800A04 Product information Product started by RUN MODE "PASS"Operation.
800B01 Machine Interface No signal from furnace.
Signal
800C01 Cancel Recovery on
(Contents) Self-Diagnostics Error Message
(Description) Confirm the displayed contents.
800D01 Maintenance Trash box fill up warning.(notice count over)
Warning
800D02 Maintenance Keep the machine condition.(maintenance cycle time : Oil-
Warning Checkup/Weekly)
800D03 Maintenance Keep the machine condition.(maintenance cycle time : Oil-
Warning Checkup/1-Monthly)
800D04 Maintenance Keep the machine condition.(maintenance cycle time : Oil-
Warning Checkup/3-Monthly)
800D05 Maintenance Keep the machine condition.(maintenance cycle time : Oil-
Warning Checkup/6-Monthlyy)
800D06 Maintenance Keep the machine condition.(maintenance cycle time : Oil-
Warning Checkup/Designate #1)
800D07 Maintenance Keep the machine condition.(maintenance cycle time : Oil-
Warning Checkup/Designate #2)
(Contents) Self-Diagnostics Error Message
(Description) Follow the displayed instructions for maintenance work.
1.3 Machine lnformation
0305-001 2-16 AIL01ETRP
Check Code Display Section A Display Section B
800D08 Maintenance Keep the machine condition.(maintenance cycle time : Upkeep-
Warning Checkup/Nozzle)
800D09 Maintenance Keep the machine condition.(maintenance cycle time : Upkeep-
Warning Checkup/Filter #1)
800D0A Maintenance Keep the machine condition.(maintenance cycle time : Upkeep-
Warning Checkup/Filter #2)
800D0B Maintenance Keep the machine condition.(maintenance cycle time : Designate-
Warning Checkup/Item #1)
800D0C Maintenance Keep the machine condition.(maintenance cycle time : Designate-
Warning Checkup/Item #2)
800D0D Maintenance Keep the machine condition.(maintenance cycle time : Designate-
Warning Checkup/Item #3)
800D0E Maintenance Component box fill up warning.(notice count over)
Warning
(Contents) Self-Diagnostics Error Message
(Description) Follow the displayed instructions for maintenance work.
800E01 Program Change Check the setup of machine.(program change completed)
Warning
800E02 Program Change "Check the setup of machine.(Program change completed. Run
Warning Mode changed to "PASS".)"
800F01 SIF information The fdr.was not recorded SIF data exists. Please record by
mnl.operation.
800F02 SIF information The SIF data was changed. Please record by mnl.operation.
800F03 SIF Information The fdr. was not recorded SIF data exists.
Please record by mnl.operation.
800F04 SIF Information The fdr.was not recorded SIF data exists.
800F05 SIF Information "Performing this operation may cause unrecorded SIF data lost.
Press Enable SW during lit, if continue."
800F06 SIF Information Changing the feeder alternate condition to 'Disable' for SIF found
empty feeder.
800F07 SIF Information Changing the feeder alternate condition to 'Disable' for SIF found
missing feeder.
(Contents) Self-Diagnostics Error Message
(Description) Confirm the displayed contents.
1.3 Machine lnformation
0511-002 2-17 AIL01ETRP
Check Code Display Section A Display Section B
801001 Auto Offset Teach Auto offset teach mode start.(this prcs. Completed)
Information
801002 Auto Offset Teach Nozzle offset error.
Information
801003 Auto Offset Teach Nozzle Dirt Detection. If dirt has adhered, there is a possibility
Information that it may become impossible to recognize. Please remove the
ring lighting glass upper surface, a diffusion board, and the dirt
adhering to the nozzle.
801004 Auto Offset Teach Gain Level Teach Error.
Information
801005 Auto Offset Teach "Camera Dirt Detection. If dirt has adhered, there is a possibil-
ity Information that it may become impossible to recognize.
Please remove the ring lighting glass upper surface, a diffusion
board, and the dirt adhering to the nozzle."
801006 Auto Offset Teach Nozzle center error.
Information
801007 Auto Offset Teach Nozzle origin error.
Information
801008 Auto Offset Teach Nozzle Posture Level
Information
801101 Feeder Carriage Return to order of priority carriage.
Priority Mode
801201 Start Auto Head Cpu Communication error occurred.(CPU2-CPU3)
Recovery
801202 Start Auto Head Head cam origin return action not complete.(Not CAM ORIGIN
Recovery position)
801203 Start Auto Head Head Driver communication is time out.(from cpu3 job)
Recovery
801204 Start Auto Head Nozzle change action not complete.(cam lock action NG)
Recovery
801205 Start Auto Head Head cam position return action not complete.
Recovery
801206 Start Auto Head Nozzle change action not complete.(cam free action NG)
Recovery
801207 Start Auto Head Nozzle change action not complete.(Not CAM ORIGIN position)
Recovery
(Contents) Self-Diagnostics Error Message
(Description) Confirm the displayed contents.
1.3 Machine lnformation
0511-001 2-17-1 AIL01ETRP