4OM-1003-007.pdf - 第206页

(8) When the message "W arm Start Enable" is displayed in the "Operator Message" pane in the "AUTO OPN." window , it means that the "W arm Start" operation is feasible. (a) "W…

2.3 [EMERGENCY STOP] Switch Pressed

2.3.1 During Automatic Operation

Table 4B5

Symptom (1) The [POWER ON] button turns red and the following window opens.

Fig. 4B7

Cause (1) An [EMERGENCY STOP] switch was pressed.

Remedy (1) Press the [RETURN] button.

(2) Check for fallen components and remove them if any.

Check the areas below the vacuum nozzles located between Stations #12

and #6.

Especially, when a component has fallen on the camera in the component

recognition section (Station #3), be sure to remove it.

(3) Check the tape feeders.

When a component to be picked up still remains in the cavity of a tape,

remove it from the cavity.

(4) Unlock the [EMERGENCY STOP] switch.

(5) Hold down the [POWER ON] button for more than 1 second to re-supply

power to the machine.

• When the LED of the [POWER ON] button turns yellowish green, it indi-

cates that power is supplied to the machine.

When the LED is kept red, re-check the cause and remove it.

(6) Press the [ALL] button (entitled "ZERO") in the "AUTO OPN." window. In 2

seconds, press the [ENABLE] button on the operation panel to zero all

devices.

(7) Check whether or not the P.C.B. in the middle of component placement is

located out of the positioning section or the components are normally placed

(not dispersed).

0305-001 2-25 AIL01ETRP

2.3 [EMERGENCY STOP] Switch Pressed

(8) When the message "Warm Start Enable" is displayed in the "Operator

Message" pane in the "AUTO OPN." window, it means that the "Warm

Start" operation is feasible.

(a) "Warm Start Enable" means that the production is interrupted in

the middle of component placement.

(b) When the operation is interrupted without any component being

placed, "Warm Start" becomes impossible.

Fig. 4B8 "AUTO OPN." Window (Submenu)

(9) Press the [OPN. MODE] button on the submenu bar. The "OPN. MODE"

window (submenu) opens.

Fig. 4B9 "OPN. MODE" Window (Warm Start Available Mode)

(a) When the "Warm Start" operation is feasible, the [WARM] button

appears in the "OPN. MODE" window (submenu).

(b) When the [WARM] button is not displayed, it means that the "Warm

Start" operation is not feasible or there was a mistake in the re-

medial procedure after an error had occurred. In this case, per-

form the semi-automatic operation (step designation) to reset the

machine to its normal condition.

2.3 [EMERGENCY STOP] Switch Pressed

0412-002 2-26 AIJ01ETRP

Note

(10) Check how the last component was placed when the operation was in-

terrupted.

The last placement step is indicated in the "Start Step" group box in

the "OPN. MODE" window (submenu).

Check visually whether or not the relevant component is placed on

the P.C.B.

(11) Press the [Last Placed Pos.] button (entitled "Move Table X/Y") in the

"OPN. MODE" window (submenu).

(12) Press the [RECOG.] button on the main menu bar and make the recog-

nition window (1/4 of the whole view at the upper right corner) appear.

(13) Press the [ON] button (entitled "MOVE"). In two seconds, press the [EN-

ABLE] button on the operation panel.

The last placement position is displayed as a recognition image.

Fig. 4B10 "OPN. MODE" Window (Last Step Confirmation)

(14) Check whether or not the component is placed. If not, select the [Place-

ment] button. If the component is already placed, select the [Not Place-

ment] button.

(15) Press the [Zero] button (entitled "Move Table X/Y") and press the [ON]

button (entitled "MOVE"). In two seconds, press the [ENABLE] button on

the operation panel. The X/Y Table is zeroed.

(16) Press the [START] button on the operation panel. The "Warm Start"

operation is implemented.

(17) As for the P.C.B. produced through "Warm Start" operations, be sure to

confirm that all components are correctly placed.

2.3 [EMERGENCY STOP] Switch Pressed

0412-002 2-27 AIJ01ETRP

Note