88242361-04-01 Vol 1 DEK TQ TECHNICAL REFERENCE (1).pdfPDFA.pdf - 第178页
10 STENCIL ALIGNMENT MODULE 10.3 ADJUSTMENTS AND SETTINGS 178 TECHNICAL REFERENCE MANUAL DEK TQ 04/2021 10.3 ADJUSTMENTS AND SETTINGS 10.3.1 Stencil Width Adjustment W ARNING BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED …
10 STENCIL ALIGNMENT MODULE
10.2 ELECTRICAL SCHEMATIC
TECHNICAL REFERENCE MANUAL DEK TQ 04/2021 177
Machine Controller
Controller Power Module
(CPM)
Fibre
Optic
Links
Ribbon Cables
SIO Link Cable
M
M
Coplanarity
Left
MTR22
Coplanarity
Right
MTR23
Extended Power Module
EPM1-1
J6
J7
MTR22
MTR23
6SE2A
ADC/DAC
Board 6
ESIO
Upper Frame 4
6PL3
6SE1A
6PL6
Amplifier
Amplifier
Coplanarity
Laser Left
6SE1
Coplanarity
Laser Right
6SE2
12 12
12 12
Coplanarity
Right Home
3SE6
IO1
IO2
IO16
6PL7
6PL8
Coplanarity
Left Home
3SE5
Sensor
Sensor
Auto Coplanarity
10 STENCIL ALIGNMENT MODULE
10.3 ADJUSTMENTS AND SETTINGS
178 TECHNICAL REFERENCE MANUAL DEK TQ 04/2021
10.3 ADJUSTMENTS AND SETTINGS
10.3.1 Stencil Width Adjustment
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
The chase holders are adjustable to suit various widths of stencil. Their positions are adjusted
manually, using the following method:
1. Shut down the software.
2. Switch the mains isolator to OFF.
3. Open the front cover.
4. Remove the rear upper panel.
5. Release the surplus pneumatic tubing (2) from the clips (1) on the left and right hand sides.
1
1
2
2
6. On the right hand side of the chase, using a 4mm Allen key, loosen the four securing screws
(1) that secure the adjustable stencil holder at the front.
1
10 STENCIL ALIGNMENT MODULE
10.3 ADJUSTMENTS AND SETTINGS
TECHNICAL REFERENCE MANUAL DEK TQ 04/2021 179
7. Loosen the four securing screws (1) that secure the adjustable stencil holder at the rear.
1
8. Repeat Steps 6 and 7 for the left hand side.
9. On the right hand side, slide the stencil holder to the required position using the etched di-
mension marker on the chase frame. Ensure that the pneumatic tube at the rear does not
snag.
10. Secure (but do not tighten) one of the screws at the rear.
11. Check that the front is aligned to the etched dimension marker on the chase frame and secure
(but do not tighten) one of the screws.
12. Repeat Steps 9 to 11 for the left hand side.
13. On the rear left hand side, tighten the four securing screws to 10.5Nm ±0.5Nm. Do not over-
tighten.
14. Loosen the securing screw at the front to ensure there is no tension forcing the chase holder
to the left or the right.
15. On the front left hand side, tighten the four securing screws to 10.5Nm ±0.5Nm. Do not over-
tighten.
16. Repeat Steps 13 to 15 for the right hand side.
17. Secure any surplus tubing in the clip and secure the clip.
18. Refit the upper rear panel.