Printer 710_810 v8 Transportation.pdf - 第97页

TRANS PORTATION PRE POWER UP CHECKS Chapter Issue 7 Oct 06 Technical Reference Manual 34.97 Pneumatic Supply The machin e requires a pneumatic supply of cl ean, non lubr icated air whi ch should maint ain a minimum press…

100%1 / 120
TRANSPORTATION
PRE POWER UP CHECKS
34.96 Technical Reference Manual Chapter Issue 7 Oct 06
External Services
In order for the machine to function correctly the following services must be
available:
• Pneumatic Supply
• Electrical Supply
Other services that may be required are:
• Host Communications
• Upline/Downline Machine Interface (FMI/MIU)
• Temperature Control Module (TCM)
Item Description Item Description
1 Printer Mains Supply Cable 4 Foreign Machine Interface (FMI) Pod
2 Temperature Control Module (TCM) 5 Air Connection
3 Host Comms LAN RJ45 6 Multi Interface Unit (MIU)
M
1S
K1
M1SK1
U
PL
IN
E
UPLI
NE
M
1
SK
2
M1SK2
D
O
W
N
L
I
N
E
DO
W
NLINE
M
1
P
L3
M
1PL3
DE
K
M
/C
DEK
M/C
M
1
S
K
4
M
1S
K
4
D
EK
US
B
DE
K
USB
+1
2
V
+12V
+24
V
+24V
+2
4V
S
W
+24V
SW
S
EN
D
U
PL
IN
E
SE
ND
UP
LI
N
E
SE
ND
D
OW
NL
I
N
E
S
E
ND
D
OWN
L
I
N
E
C
ON
T
R
OL
I
N
CO
NTR
OLI
N
U
PLI
NE
R
EA
D
Y
UPL
I
NE
READ
Y
DO
W
N
LIN
E
RE
A
D
Y
DOWNLINE
READY
CO
NT
R
O
L
O
UT
C
ON
TROLOUT
P
O
W
E
R
PO
W
ER
I/P'
S
I/P'
S
O
/
P
'
SO
/
P
'
S
P
R
O
T
O
C
OL
S
EL
E
C
T
I
O
N
P
R
O
T
O
C
OLSELE
C
TIO
N
U
P
UP
L
IN
E
LI
NE
D
OW
N
DOWN
L
IN
E
LI
N
E
M
IU
1
9
1
11
4MIU
191114
4
8
0
4
8
0
POWER ON
PART No. 160740
M/C AVAILABLE
BOARD AVAILABLE
BOARD PASS
D
O
W
N
LIN
E
BOARD AVAILABLE
BOARD PASS
M/C AVAILABLE
U
P
LIN
E
FMI POD
View on RearView on Front
1
2
3
4
5
6
M1SK1
UPLINE
M1SK2
DOWNLINE
M1PL3
DEK M/C
M1SK4
DEK USB
+12V
+24V
+24V SW
SEND UPLINE
SEND DOWNLINE
CONTROL IN
UPLINE READY
DOWNLINE READY
CONTROL OUT
POWER
I/P'S
O/P'S
PROTOCOL SELECTION
UP
LINE
DOWN
LINE
MIU 191114
4
80
4
80
TRANSPORTATION
PRE POWER UP CHECKS
Chapter Issue 7 Oct 06 Technical Reference Manual 34.97
Pneumatic Supply The machine requires a pneumatic supply of clean, non lubricated air which
should maintain a minimum pressure 5 Bar and a maximum of 8 Bar.
The air should be to ISO 8573.1 standard, quality class 2.3.3, where:
• 2 dirt = 1 micron
• 3 water = -20°C pressure dewpoint
• 3 oil = 1mg/m3
Electrical Supply The factory mains supply for the machine is routed through the front panel
mounted mains isolator switch and on to the M37 power supply enclosure where
various low voltages are distributed throughout the machine.
Figure 34-26 Mains Electrical Supply
The machine operates on 100V to 240V +
10% 50/60Hz single phase ac mains.
DEK recommends a power supply capacity of 2.4KVA or greater.
DEK requires additional machine supply protection with the fitment of an
external double pole circuit breaker conforming to national, federal or local
legislation. Use the following table to ensure the recommended circuit breaker
is used:
CAUTION
OVER CURRENT PROTECTION.
An over current circuit breaker protects the
machines internal wiring and components from overheating or catching
fire during fault conditions. Under no circumstances must a circuit
breaker of value greater than 25 Amps be fitted.
Voltage Value of Wall Mounted Circuit Breaker
(without Internal Vacuum Unit)
Value of Wall Mounted Circuit Breaker
(with Internal Vacuum Unit)
115V 10 Amp 25 Amp
230V 4/6 Amp 13/16 Amp
To Factory Mains Supply
Mains Isolator
Switch
M37 Power Supply Enclosure
TRANSPORTATION
PRE POWER UP CHECKS
34.98 Technical Reference Manual Chapter Issue 7 Oct 06
Preparations 1. Ensure machine mains isolator is OFF.
2. Check and verify that the mains electrical supply is single phase 100V to
240V +
10% at 50/60Hz ac.
3. Check that all circuit breakers are in the ON position.
4. Ensure that all access covers and removable panels are closed and are in
place.
5. Ensure that the E Stop button is in the fully out position. To check this, push
the E Stop button until it latches. Turn the button clockwise to release it.