Portal-Operation-Manual-REV-I.pdf - 第4页
PVA Portal Manual Revision I / Janua ry 2022 Page 4 of 106 6.6.1 Vision Window ................................................................................................................. 26 6.6.2 Manual Mode Vision…
PVA Portal Manual
Revision I / January 2022
Page 3 of 106
Table of Contents
Introduction ........................................................................................................... 7
1.1 PVA Contact Information ........................................................................................................ 7
1.2 Document History ..................................................................................................................... 7
1.3 Safety ......................................................................................................................................... 8
1.4 System Description ................................................................................................................ 10
1.5 Personal Protective Equipment ........................................................................................... 10
1.6 PVA Portal Computer Requirements ................................................................................... 11
1.6.1 Galil Controller Requirements ....................................................................................... 11
1.6.2 Security Software ............................................................................................................ 11
1.7 Operator Skills ........................................................................................................................... 11
Installation and Recovery .................................................................................. 12
2.1 Install Portal Shell or Portal .................................................................................................. 12
2.2 Backup Portal........................................................................................................................... 12
2.3 Restoring Portal ...................................................................................................................... 12
System Overview ................................................................................................. 13
3.1 Software ................................................................................................................................... 13
3.1.1 Portal ................................................................................................................................. 13
3.1.2 PathMaster® .................................................................................................................... 13
3.2 Teach Pendant ........................................................................................................................ 13
Portal Shell Overview ......................................................................................... 15
4.1.1 Portal Shell Keyboard Shortcuts ................................................................................. 16
Portal Overview ................................................................................................... 17
5.1 Cycle Stop Interface ............................................................................................................... 18
5.2 Program Selection .................................................................................................................. 19
Manual Mode ....................................................................................................... 20
6.1 Device Selection ...................................................................................................................... 21
6.2 Run Mode ................................................................................................................................. 22
6.4 SMEMA Status ........................................................................................................................ 24
6.6 Vision ........................................................................................................................................ 26
PVA Portal Manual
Revision I / January 2022
Page 4 of 106
6.6.1 Vision Window ................................................................................................................. 26
6.6.2 Manual Mode Vision Window ........................................................................................ 27
6.6.3 Quick FID Inspection...................................................................................................... 30
6.6.3.1 Create a New Inspection .............................................................................................. 30
6.6.3.2 Editing Inspections ........................................................................................................ 32
6.6.3.3 Preview Mode .................................................................................................................. 33
6.7 Conveyor Controls ................................................................................................................. 34
6.8 FIS .............................................................................................................................................. 35
6.8.1 FIS Client Mode Screen ................................................................................................. 35
6.8.2 FIS Client Message Screen ........................................................................................... 36
Auto Mode ............................................................................................................ 38
Setup Mode ........................................................................................................... 39
8.1 System ..................................................................................................................................... 39
8.2.1 Standard Calibration ..................................................................................................... 40
8.2.2 Sensor Defined Tool Calibration ................................................................................. 42
8.4.1 Gantry Speed .................................................................................................................. 44
8.4.2 Low Level ......................................................................................................................... 46
8.4.3 Machine Idle .................................................................................................................... 47
8.4.4 Pressure Monitoring ...................................................................................................... 48
8.4.5 Scales ............................................................................................................................... 49
8.4.6 Vision Teach Tool ........................................................................................................... 49
8.4.7 FIS ....................................................................................................................................... 51
8.4.8 Flow Monitors................................................................................................................... 51
8.4.8.1 Priming the Flow Monitor .............................................................................................. 51
8.4.8.2 Finding the Correct Material Volume ......................................................................... 52
8.4.8.3 Set the Material Volume Check ................................................................................... 53
PVA Portal Manual
Revision I / January 2022
Page 5 of 106
8.4.8.4 Auto Cycle Flow Error ................................................................................................... 53
8.4.8.5 Flow Monitor Calibration .............................................................................................. 54
8.4.9 Needle Calibration .......................................................................................................... 55
8.4.10 Program Select ............................................................................................................... 56
System Tabs ......................................................................................................... 57
9.1 Product Image ......................................................................................................................... 57
9.1.1 Adding Product Images ................................................................................................ 58
9.2 Process ..................................................................................................................................... 58
9.2.1 Product ............................................................................................................................. 58
9.3 Terminal ................................................................................................................................... 59
9.4 I/O .............................................................................................................................................. 60
9.5 Gauges...................................................................................................................................... 62
9.6 Scales ....................................................................................................................................... 63
9.7 FIS .............................................................................................................................................. 64
9.8 Laser ......................................................................................................................................... 64
9.9 Lights ........................................................................................................................................ 65
Operation .............................................................................................................. 66
10.1.1 Portal Shell ....................................................................................................................... 67
10.1.2 Login to Portal ................................................................................................................ 68
10.2 Exhaust Verification .............................................................................................................. 68
Portal Permissions .............................................................................................. 73
Portal Communications ...................................................................................... 77
DataView.............................................................................................................. 80
13.1 Startup Log File ...................................................................................................................... 80
Part Manager....................................................................................................... 82
14.1 Part Selection Console ......................................................................................................... 82
14.2 Recipe Manager ...................................................................................................................... 83
14.2.1 To Edit Part Name or Part ID ........................................................................................ 85
14.2.2 To Edit a Property Field ................................................................................................ 85