00196962-04-BA-SX12-V2-EN.pdf - 第203页
User manual SIPLACE SX1/SX2 4 Setting up and commissioning From software version SC 706.1 SP1 Version 10/2014 4.3 Setting up the machine 203 4.3.3.2 Fitting the indicator lamp Insert the indicator lamp into th e hole u…
4 Setting up and commissioning User manual SIPLACE SX1/SX2
4.3 Setting up the machine From software version SC 706.1 SP1 Version 10/2014
202
4
4
4
4.3.3 Fitting attached parts
The machine is delivered with the monitor, operating panel, keyboard and indicator lamp disman-
tled. To fit these components, proceed as follows:
– To fit the indicator lamps see section 4.3.3.2
, page 203
– To fit the monitors see section 4.3.3.3, page 203
– Hook up the keyboard fixture and connect the keyboard.
4.3.3.1 Checking and setting the protective cover switch
Check the function of the protective cover switch (see 2.5.1 on page 56).
Adjust the protective cover switch if necessary (see service manual).
WARNING
Risk of damage due to excessive fork spacing!
Increased fork spacing, which means that the machine is raised at points outside its con-
tact surface, can lead to deformation of the machine frame and cause damage to cables
and lines.
The forks may only be opened to a degree which ensures that they are still within the
contact area of the machine underside (see fig. 4.1 - 3
, page 189).
WARNING
Risk of damage due to one-sided loading!
One-sided loading of the machine feet e.g. from tilting the machine, can lead to deforma-
tion of the machine feet.
Make sure that the forks are evenly loaded when you lift the machine.
Use a firm support layer between the forks and the machine.
Enlist the help of a second person to watch while you lift the machine and make sure
that the machine does not tip over to one side.
WARNING
Risk of damage!
The thread for the machine feet in the machine frame could be damaged by being
dragged along the floor or from impact.
When you are transporting the machine, make sure that all the feet are clear of the
floor.
User manual SIPLACE SX1/SX2 4 Setting up and commissioning
From software version SC 706.1 SP1 Version 10/2014 4.3 Setting up the machine
203
4.3.3.2 Fitting the indicator lamp
Insert the indicator lamp into the hole until the lamp tube projects sufficiently into the terminal
beneath.
Connect the cable for the indicator lamps to the connector. The cable with connector is lo-
cated in the tube.
Tighten the two screws on the terminal so that the indicator lamp is clamped into place.
4.3.3.3 Fixing the monitors
Use the 4 fastening screws to fix the monitor to the monitor mount and then connect the cable.
Check the cable connections.
4.3.4 PCB conveyor height on the machine
The machine can be set to the following PCB conveyor heights:
900 mm ± 15 mm 4
930 mm ± 15 mm (standard height) 4
950 mm ± 15 mm (SMEMA height) 4
4
PLEASE NOTE
The PCB conveyor height is the distance between the top edge of the PCB conveyor belt
and the bottom edge of the machine feet.
4 Setting up and commissioning User manual SIPLACE SX1/SX2
4.3 Setting up the machine From software version SC 706.1 SP1 Version 10/2014
204
4.3.5 Tools and equipment
You will need the following tools and equipment to adjust the height of your machine:
– Combination wrench size 19, Item No. 03111261-01 (new)
– Or, optionally: Open double-ended ring spanner, size 20, Item No. 03080496-01
– Torque wrench with setting scale, Item No. 03080498-01 and extension 1/2 inch, Item No.
03080499-01
– Hexagonal screwdriver bit, size 12 Item No. 03080501-01
– Hexagonal screwdriver bit, size 14 Item No. 03080502-01
– Allen key, for hexagon socket head screws for fixing the machine feet with a grub screw
– Shaft spirit level (accuracy 0.02 mm/m), item no. 00353825-01
– Measuring device for machine alignment, Item No. 03075826-01
as support for the shaft spirit level used to align the gantries. 4
– SX machine alignment gauge 2 assembly, item no. 03077785-01
– SX machine alignment gauge 1 assembly, item no. 03077777-01
for alignment to the PCB conveyors in the line 4
– Fork lift truck (specification see 4.1.4.3 on page 186).
– Air cushion transport system: SIPLACE HSxx, Item No. 00119002-S01 (optional)