00191913-01.pdf - 第458页
11 Station extensions / hardware User Manual SIPLACE 80S- 20/F4 11.1 Nozzle changer for the 12-segment revolver head Software version SR.406.xx 02/2000 Issue US 456 11 Fig. 1 1.1 - 2 Magazine and nozz le holders 11 (1) P…
User Manual SIPLACE 80S-20/F4 11 Station extensions / hardware
Software version SR.406.xx 02/2000 Issue US 11.1 Nozzle changer for the 12-segment revolver head
455
PLEASE NOTE 11
Special magazines are available upon request, and are given a special identification. Please con-
tact Siemens PL EA 1E to discuss. 11
Picking up a nozzle 11
– The revolver head Z-axis moves down.
– The locking plate (item 3 in Fig. 11.1 - 2) opens and releases the nozzles.
– The nozzle is picked up from the sleeve of the revolver head.
– The Z-axis moves up.
Returning a nozzle 11
– The locking plate (item 3 in Fig. 11.1 - 2) opens and releases the nozzles.
– The revolver head Z-axis moves down and releases the nozzle.
– The locking plate closes.
– The revolver head Z-axis moves up.
Rejecting defective nozzles 11
– At the reject device (item 2 in Fig. 11.1 - 1), the revolver head Z-axis moves down 14 mm, and
thus feeds the defective nozzle into the hole in the reject device.
– The Z-axis moves up again, and the nozzle is removed from the sleeve by spring wires.
– The nozzle drops into the collecting tray of the empty tape track (item 3 in Fig. 11.1 - 1).
11 Station extensions / hardware User Manual SIPLACE 80S-20/F4
11.1 Nozzle changer for the 12-segment revolver head Software version SR.406.xx 02/2000 Issue US
456
11
Fig. 11.1 - 2 Magazine and nozzle holders
11
(1) Position fiducial
(2) Locking plate
(3) Nozzle holder
(4) Hole for the parallel pin (7) for centering the magazines
(5) Hole for the parallel pin of the moving mechanism
(6) Slot for the parallel pin (7) for centering the magazines
(7) Parallel pin for centering the magazines
(8) Parallel pins for opening and closing the locking plate
(9) Magazines
User Manual SIPLACE 80S-20/F4 11 Station extensions / hardware
Software version SR.406.xx 02/2000 Issue US 11.1 Nozzle changer for the 12-segment revolver head
457
11.1.4 Notes on operation
Å When you fill a magazine with a certain nozzle type for the first time, mark the magazine with
an adhesive label.
PLEASE NOTE 11
Only one nozzle type must be used in each magazine.
Fill the magazines off the machine, and always replace complete magazines. 11
Å Open the locking plate, and insert the nozzles into the nozzle holders.
Å Close the locking plate so that the nozzles cannot drop out of the magazines.
CAUTION 11
The magazines must not be filled until all the nozzles on the revolver head have been re-
turned to their magazines. 11
Å See the UNIX line computer user manual for instructions on programming the nozzle changer
on the line computer.
PLEASE NOTE 11
Å Be careful not to drop components onto the magazines, since they could cause the locking
plate to jam.
Å Also avoid dropping components onto free feeder locations, since the components will stick to
the magnetic bar. The work flow may be interrupted if the feeders are not placed on the com-
ponent feeder table correctly. You should therefore regularly clean the magazines and free
locations.