SIPLACE Vision Customer_en.pdf - 第181页

Function: Menu 1 Menu 2 Menu 3 Menu 4 Nozzles Cameras acceleration Vacuum at pickup: Normal Vacuum; it is activated when the nozzle touch the component. Early Vacuum; it is activated when the Z-Axis trigger the LB-topb (…

Feature

PIN type

Shape & Meas.

position

0 degree

orientation

Filter for feature

(terminal) Speciality / comment

used at ...

Possible to use at ...

Reason for reject of the GF-

type

Rectangle

feature since

702(sv4.0.1)

The rectangular feature could be a feature of

the comp. Beside the electr. Terminals. But it

could be also the hole component.

the min. respectively thie max. size

depend on the camera type. only for Nonstandard

Edition 3.0 17.10.2008 GF kurzref_A4_DE.xls features Siemens Ind. Sec EA1 SC E

Function: Menu 1 Menu 2 Menu 3 Menu 4

Nozzles

Cameras

acceleration

Vacuum at pickup:

Normal Vacuum; it is activated when the

nozzle touch the component.

Early Vacuum; it is activated when the Z-Axis

trigger the LB-topb (DLM). C&P20 head: The

Vacuum ispermanent on the nozzle. For

comp.'s smaller 6mm is recommended to

switch to early Vacuum by default.

pickup correction:

autom. pickup-pos-corr. ON? is only

deactivated for 'MELF' and ODDshape GF's.

A Z-pickup height corr. is always active!!

X/Y/Z pickup position (offset) program a

shift of the nozzle contact point to the GF-

center. the comp. is picked there to avoid

leaking or swiffle of an unsymetric c.

MTC-acceleration:

Y-axis valid for the feed axis of the Magazine

carriers

Z-axis valid for the lift axis of the respective

Magazine tower

centering:

activate centering: is deactivated in very rare

exceptions (placement force measurement).

Reduce optical width : is as a LC-Import /re-

export function implemented.

coplanarity: is to activate here. The coplan.

Tolerance is the solder paste thickness at the

PCB-editor.

Dipp: Special mode for Flux material at comp.

terminals in DIP-modul on feeder area.

It isto select: Dipp

/ Dipp before Vision/Vision

before Dipp

force for Dipp / Waiting time in Flux

Pickup pos. offset to the standard pickup

pos. in center of the feeder pickup window

Feeder fiducial: (for X-feeder)

A programming option forteached feeder

position recognition fiducial. This is an option

for special cases or if the general function fail.

Transport speed: (for X-feeder)

The transport speed for the comp. tape could

be reduced to middle or slow.

component pitch: (for X-feeder transfered

into feeder)

The comp. pitch in the reel -information for

traceability at S-feeder.

Comments

Airkiss at

placement/re

turn

adjustable

airkiss

C&P20/TWIN.

At DLM head -

time

controlled in

placement

sequence.

Speed profile for pickup:

Profile downward: 1 - pickup stand. - with contact (2N) / 17 - Pickup contactless (with autom. height teaching at 1st pickup) 21 pickup with minimal force (1N Twin only) 22 ----

Profile upward: 2 pickup stand. Normal accel. upward 3 start slowly upward (20ms for full vacuum) 4 - start very slow upw. (very time consuming) 23 ---

Speed profile for placement: downward define the placement force for the component.

Profile downward: 5 placement stand. 2N -force 7 - increase -force 3- 5(C&P) -10N IC/TWIN 8 - increased -force with slow touch down (+20ms) 3- 5(C&P) -10N IC/TWIN

25 very high -kraft 11-15N TWIN 26 very high force w. slow touch down 11-15(30) TWIN 27 very low -force 1.0N only TWIN 28 very low -force w. slow touch down TWIN 29/30 --- 31

smooth placement (for 0201)

Profile upward: 9 standard upward 10 slow start upward (+~20ms) 24 ---?

sorted according head type / selected that they fit for the body dimension and comp. height / they should have enough holding force to the comp. surface during the placement sequence

(nozzle material) see nozzle overview

placement head specific; consider maximum comp. size; consider min. pitch and structures; see camera overview

The acceleration of axes base on the SIPLACE machine type with the fastest axis of the selected type. Therefore program this reduced values only with assistance of ONLINW HELP

information. The values are programed in absolute values in 'g' or r/sec².

-> for shiffted components on nozzle: 1. check selected nozzle, nozzle material 2. check acceleration X/Y respect. / and Star axis

-> for turned comp.'s (angle error in the camera) 1. check selected nozzle, nozzle material 2. check accel. Z-axis upw. 3. reduce accel. DP-axis.

-> comp.-pickup error 1. check feeder 2. check special mode for improvement 3. reduce (additional) accel. Z-axis upward.

Feeder

Comp.-presence check: activ./deactiv. for Pickup and/or placement (deselect both or select NO Vacuum)

-> Normal: at C&P6/12 head - a vacuum check is done / C&P20 - comp. presence check with comp.-sensor / TWIN - vacuum check

Extended: at C/P12 /20 head - comp. presence check with comp. sensor (option) C&P6 /TWIN ---

-> comp. thickness: DLM12 with comp.sensor opt. measure comp-thickness & at the same time vacuum check / C&P20 measure

comp.thickness at nozzle / TWIN ---

-> comp. thickness and NO Vacuum: C&P12 with comp. sensor opt. & C&P 20 head measure comp. thinkness ./ TWIN ---

For X- Feeder programming of GF / component please note:

-> with manual programming of the Feeder the programmed pickup offset of the org. feeder are NOT taken and prog.

-> with automatic programming of the Feeder the programmed pickup offset of the org. feeder are taken and prog.

A meaningfull comment for the component shape help the operator and programmer.

basic

handling

Placement force:

values for C&P head from 1N to 5N

for IC head (Fx ma.) 1-10N

for TWIN head standard 1-15N / Highforce 1-30N

Please Note: You have to select for this Function additionally the right profil in menu

'Extended handling'; otherwise the placement head continue work with 2N placement

force.

extended

handling

Edition 3.0 17.10.2008 GF kurzref_A4_DE.xls Handling data Siemens Ind. Sec EA1 SC E

Camera type for

Ma. with ICOS in

Siplace pro

Description /

Head / Machine Picture

Field of View

FOV/

resolution

Component

size min. feature size Illumination

SST5

PCB-Camera

standard

Standard for all

machine till HF

5,8x 5,8 mm

~12µm/Pixel

Fiducial size

3x3 mm

depending on fiducial

type until min. 0,3mm

edge length

white (add. option

blue LED-Ill.)

SST18

PCB-Camera

multi color

Option for

S27/HS/HF

5,8x 5,8 mm

10µm/Pixel

Fiducial size

3x3 mm

depending on fiducial

type until min. 0,3mm

edge length

white,white diffuse,

IR, IR diffuse, blue

Lead width suit to the

contact length

PP Cam 7

SST7

IC-Camera

F3/F4

F3…F5HM

36x36mm

79µm/Pixel

32x32mm

Single, 55 x55

mm multiple

measurement

0.5 x 0.5mm (0402)

lead pitch 0.4mm /

lead width 0.2mm /

ball pitch 0.5mm /

ball-diam. 0.3mm

Red LED's in 3

levels

PP CAM 10

SST10

IC-Camera

F4…F5HM

36x36mm

79µm/Pixel

32x32mm

Single, 55 x55

mm multiple

measurement

0.5 x 0.5mm (0402)

lead pitch 0.4mm /

lead width 0.2mm /

ball pitch 0.5mm /

ball-diam. 0.3mm

Red LED's in 4

levels

PP CAM 11 C4

SST11

FlipChip-

Camera IC Head

F3…F5HM

~12x10 mm

~20µm/Pixel

7x7 mm single

measurement

lead pitch 0.2mm /

~ lead width 0,1 mm /

ball pitch 0.14mm /

ball-diam. 0.100mm

Red LED's in 3

levels

FC CAMERA

(Type20) FOV

11x11

SST20

TWIN FC-Cam.

11 x 11 mm

~19µm/Pixel 8x8mm

0.2 x 0.1mm (01005)

lead pitch 0.25mm /

lead width 0.1mm /

ball pitch 0.14mm /

ball-diam. 0.08mm

Red LED's in 6

levels

IC CAMERA

(Type 22) FOV

45x60

SST22

TWIN IC-Cam.

60 x 45mm

79µm/Pixel

50x40mm

(69x10) single,

85x85mm

(125x10) 1 noz.

with restriction

200x125mm

0.5 x 0.5mm (0402)

lead pitch 0.3mm /

lead width 0.15mm /

ball pitch 0.45m /

ball-diam. 0.25mm

Red LED's in 6

levels

PP COP 17 ILD

SST17

Coplan ILD 2000

(controlled with

sep. controller; 1

module per

mach.) F…HF

min. Pitch

0,4mm

RV CAM 12

18x18

SST12

Comp. Camera

C&P12

at C&P 12

heads from S20

to HF

24 x24 mm

50µm/Pixel 18,7 x 18,7mm

0.5 x 0.5mm (0402)

lead pitch 0.25mm /

lead width 0.15mm /

ball pitch 0.35mm /

ball-diam. 0.25mm

Red LED's in 3

levels

RV CAM 13

32x32

SST13

Comp. Camera

C&P6

at C&P 6 heads

from F5/S25 to

36 x36 mm

81µm/Pixel 32 x 32 mm

1 x 1mm (0603)

lead pitch 0.4mm /

lead width 0.25mm/

ball pitch 0.56mm /

ball-diam. 0.4mm

Red LED's in 2

levels

RV CAM 14

15x15

SST14

DCA-Camera

C&P12 / 6

Option at C&P 6

( C&P12) heads

15.6 x15.6

27,5µm/Pixel

special for

BareDie and

Flipchip

13 x13 mm

0.6 x 0.3mm (0201)

lead pitch 0.3mm /

lead width 0.15mm /

ball pitch 0.2mm /

ball-diam. 0.14mm

Red LED's in 4

levels

Edition 3.1 07.02.2008 _Kamera prog übers_ku_cu.xls Cam SIP Pro e Siemens A+D EA1 SC E