MAN00000772_SI-G200BB_SVCPDFA.pdf - 第621页
4. Basic Operations of the Multifunctional Mounter TFGB-10101-0 1 SI-G200 (B Head) Overview SHEET 6/20 [Nozzle T ype] The multifunctional mounter has three types of nozzles (s tandard, long, an d short). It uses an appro…
4. Basic Operations of the Multifunctional Mounter
TFGB-10101-01
SI-G200 (B Head) Overview
SHEET
5/20
Part Category Table (Unit: mm)
Number of Parts That Can Be Picked Up Simultaneously, Characteristics,
and Restrictions According to Each Part Category
Pickup Check Method
Rotational
Restriction
Recognition Method
Category
Number of
Parts Picked
Up
Simultaneously
Camera
Presence
Sensor
RT RN Individual Global
Pickup
Check
Camera
Rising
Nozzle
Type
A 8 Ο × Absent Absent Ο Ο Unnecessary Standard
B1 8 × Ο Absent Absent Ο × Unnecessary Standard
B2 2 × Ο Absent Absent Ο × Unnecessary Standard
C 4 × Ο Absent Absent Ο × Unnecessary Long
D 2 × Ο Present Absent Ο × Unnecessary Long
E 2 × Ο Present Absent Ο × Unnecessary Short
F 1 × Ο Present Present Ο × Necessary Long
G 1 × Ο Present Present Ο × Necessary Short
- Number of parts that can be picked up simultaneously
Number of parts that can be picked up simultaneously with no interference with parts picked up by the
adjacent index after the RN axis has been rotated once and with the tape on the top of the part cassette.
- Rotational restriction
Restriction for preventing interference with the tape on the top of the cassette when the RT or RN axis is
rotated at the pickup position. When this rotational restriction is imposed, the RT axis is rotated only
counterclockwise. In addition, the RN axis cannot even be rotated.
- Pickup check camera rising
When relevant large parts are picked up, a pickup check camera rises.
Part long side length
0～10 ～20 ～40 ～100
～4.0
～10.5
～13
Part thickness
～6.5
～7.5
E
F
G
B1
B2
A
C
D
4. Basic Operations of the Multifunctional Mounter
TFGB-10101-01
SI-G200 (B Head) Overview
SHEET
6/20
[Nozzle Type]
The multifunctional mounter has three types of nozzles (standard, long, and short). It uses an appropriate
one of these nozzles according to the part categories and picks up parts.
Nozzles corresponding to the part categories are shown in the table below.
Nozzle Types According to Part Categories
Category Nozzle Type Nozzle ID Nozzle Length Remarks
A,
B1, and B2
Standard 201 to 300
Same as the
standard nozzle
-
C,
D,
and F
Long 301 to 400
0.5 mm longer
than the standard
nozzle
Parts picked up by the long nozzle do not interfere
when the adjacent index is the standard nozzle.
E
and G
Short 401 to 500
5 mm shorter than
the standard
nozzle
Used for parts with a thickness of 10.5 mm or
more
<Points to Note>
- The end of the name of the long nozzle is “L” and that of the short nozzle is “S.”
Example: BF60400 (standard nozzle), BF6040L (long nozzle), BF6040S (short nozzle)
- The short nozzle is used only for parts supplied from the tray unit. (Parts supplied from the cassette
cannot be picked up.)
- The width of nozzles with large width (13 mm or more) is recognized as 13 mm.
[Pickup Check]
Concerning whether parts pickup check is carried
out or not, you can select “ON(1)” or “OFF(0)” in
“Pickup Check” displayed after selecting “Data
Editing,” “Part Management,” and “Sequence
(Multifunction)” in this order.
4. Basic Operations of the Multifunctional Mounter
TFGB-10101-01
SI-G200 (B Head) Overview
SHEET
7/20
Recognition by a Pickup Check Camera
Pickup check on parts belonging to Category A (□10 mm, part thickness: 6.5 mm or less) is carried out
with a pickup check camera used. As shown in the basic operations, parts recognition by a pickup check
camera is conducted immediately after parts have been picked up.
<Points to Note>
- Check on part thickness is carried out at the
position of the H axis being 0 mm.
- In parts recognition by a pickup check camera,
pickup check is carried out from the position
where the camera looks up at parts. Therefore,
measured thickness of parts is larger than the
actual thickness of them.
- Thin parts, even though they belong to Category
A, are not measured correctly in height and
thickness.
Recognition by a Part Presence Check Sensor
For parts belonging to categories other than A, pickup check is carried out not with a pickup check camera
but with a part presence check sensor used. Pickup check by a part presence check sensor is carried out
immediately before parts are recognized.
<Points to Note>
- Pickup check on parts with a width of less than 1 mm cannot be carried out. When parts are newly
created, “Pickup Check” is set to “OFF(0)” as default.(Even when “Pickup Check” has been set to
“ON(1),” pickup check is not carried out.)
- When pickup check is not carried with “Pickup Check” set to “OFF,” parts that have not been picked up
are not detected. Therefore, shortage of parts supplied from the cassette does not occur.
Actual part thickness
Measured thickness