4OM-1345-009_w.pdf - 第176页

3-27 AKHEMT -ID Erroe ID Error Name, Description, Cause, and Remedy 4b0406 Recycling Conveyor Component trash Box (front) was ﬁ lled Please open the safety door , and empty the comp abandonment box. 4b0501 Manual Opn Err…

3-26

AKHEMT-ID

3.9 Others

Table 4C11

Erroe ID Error Name, Description, Cause, and Remedy

4b0101 Head Mis-Pickup Detection

Auto Run can’t be performed with the Mis-Pickup Component on the head.

Please perform abandonment operation from a control menu.

4b0201 Feeder communication Error.

Communication with the feeder has error.

Please check the number of component remain.

4b0202 Feeder communication Error.

Communication with the feeder has error. (System error)

-----

4b0203 Feeder communication Error

Feeder Alarm. Please conﬁ rm the feeder and the component.

-----

4b0301 Feeder Base

The feeder base detection was turned off while the cutter was working.

-----

4b0302 Feeder Base

The feeder unclamp operation was not completed within predetermined time.

-----

4b0303 Feeder Base

Feeder operation errors

Please check after removing feeder in case using tape feeder. Please check part of

supply in case using tray.

4b0304 Feeder Base

The feeder clamp operation was not completed within predetermined time.

-----

4b0401 Recycling Conveyor

The recycling conveyer (back) was ﬁ lled.

Please push a manual switch, and remove parts on the recycling conveyer.

4b0402 Recycling Conveyor

The recycling conveyer (front) was ﬁ lled.

Please push a manual switch, and remove parts on the recycling conveyer.

4b0403 Recycling Conveyor

The recycling conveyer (back) motor operation time out.

There is a possibility a problem in the motor wiring. Please check the motor wiring.

Please begin the production.

4b0404 Recycling Conveyor

The recycling conveyor (front) motor operation time out.

There is a possibility a problem in the motor wiring. Please check the motor wiring.

Please begin the production.

4b0405 Recycling Conveyor

Component trash Box (back) was ﬁ lled.

Please open the safety door, and empty the comp abandonment box.

0609-003

3.9 Others

3-27

AKHEMT-ID

Erroe ID Error Name, Description, Cause, and Remedy

4b0406 Recycling Conveyor

Component trash Box (front) was ﬁ lled

Please open the safety door, and empty the comp abandonment box.

4b0501 Manual Opn Error

Operation was not completed within predetermined time.

-----

4b050f Manual Opn Error

Error was detected during operation.

-----

4b0601 Auto Run Start Error

Production operation has not started within predetermined time. (Please push a

start button again)

-----

4b0701 Communication Timeout

Communication failed to STG. #1 CPU

-----

4b0703 Communication Timeout

Communication failed to Recog. CPU

-----

4b0704 Communication Timeout

Communication failed to STG CPU

-----

4b0801 Linear measure operation is abnormal.

Linear measure was found abnormality while measuring.

-----

4b0901 Firmware Updating Timeout

Firmware update did not end in prescribed time.

-----

4b0a01 Feeder Alarm

Feeder Alarm. Please conﬁ rm the feeder and the component.

-----

4b0b01 Feeder base-main body connector unconnection

Feeder base-main body connector has get out of joint.

Please connect the connector of the feeder base with the main body, and push

stage preparation completion SW.

0605-002

3.9 Others

3-27-1

AKHEMT-ID

Erroe ID Error Name, Description, Cause, and Remedy

4b0c01 Nozzle Conﬁ rmation Error before pick up comp

Abandonment is stopped because comp. had been detected on the nozzle.

Please conﬁ rm and clean up the nozzle when this error continues.

4b0c02 Nozzle Conﬁ rmation Error before pick up comp

Residual components were found in the nozzle while production operation.

Please conﬁ rm whether there is an error in the PCB.

4b0c03 Nozzle Conﬁ rmation Error before pick up comp

Abandonment is stopped because comp. had been detected on the nozzle.

Please conﬁ rm and clean up the nozzle when this error continues.

4b0d01 Serial Out Mode Error

There was no response to the Serial Out Mode.

-----

4b0d02 Serial Out Mode Error

Communication failed to Shtg. of Comp. Host.

-----

4b0d03 Serial Out Mode Error

Communication with the Shtg. of Comp. Host has error.

-----

4b0e01 Splicing tape set error

The joint part of splicing tape is not correctly set.

Please extract a feeder and check whether the tape has separated from the guide.

-----

4b0f01 Decreasing of Comp. Hdlg. Rate

It stopped automatically by the rate fall of feeder adsorption.

-----

4b0f02 Decreasing of Comp. Hdlg. Rate

It stopped automatically by the rate fall of nozzle adsorption.

-----

0605-001

3.9 Others