4OM-1345-009_w.pdf - 第86页

1-30-1 AKHEMT -ID 0712-001 3.3 Inspection, Cleaning, and Lubrication Spots T ape Guide Fluorine Sheet, Urethane Clamp Every Y ear Replacement (1) Remove four screws and detach the tape guide. (2) Attach the cutter unit f…

1-30

AKHEMT-ID

WARNING

Pay close attention to the cutter blade during the maintenance

work.

Lack

of attention will result in a hand injury, etc.

Be

suretoattachthexingjigtothecutunitduringthe

maintenance work for safety purposes.

Tape Guide

Flat Ring

Every 3 Months Replacement

(1) Remove four screws and detach the tape guide.

(2) Use the inner holes of the cutter unit fixture with the tape clamp being closed and attach the jig

with the bent portion being directed upward.

Attachment Position of Cutter Unit Fixture Attachment Condition of Replacement Jig

(3) Cut the used flat ring with a cutter on market and detach it.

(4) Attach a new flat ring to the flat ring replacement jig.

(5) Place the flat ring replacement jig on the roller on the oscillating side (outside of the machine),

push down the flat ring, and insert it into the groove of the roller on the oscillating side.

Required Time: 10 minutes

When the tape guide is

detached or attached,

be sure to keep the Y-axis

linear scale free of nicks

and scratches.

Notice

Fig. 4A19-3

CAUTION

Whilecuttingtheatringwithacutteronmarket,handlethe

cutter with care to avoid getting hurt.

0712-003

3.3 Inspection, Cleaning, and Lubrication Spots

1-30-1

AKHEMT-ID

0712-001

3.3 Inspection, Cleaning, and Lubrication Spots

Tape Guide

Fluorine Sheet, Urethane Clamp

Every Year Replacement

(1) Remove four screws and detach the tape guide.

(2) Attach the cutter unit fixture with the bent portion being

directed downward.

Attachment Position of Cutter Unit Fixture

(3) Replace the fluorine sheet and the urethane clamp.

After the fluorine sheet has been replaced, activate the

cutter without the tape threaded through and cut the

fluorine sheet.

Refer to "4.3 Replacement of Fluorine Sheet and Urethane

Clamp" for the replacement procedure.

Required Time: 5 minutes

Reference

Note

Fig. 4A19-4

1-31

AKHEMT-ID

0811-003

3.3 Inspection, Cleaning, and Lubrication Spots

3.3.7 Head Section

Linear Measure Sensors

(Light Emitter and Receiver)

Every Day Cleaning

Required Time: 5 minutes

If sebum and oil, etc., adhere to the surface

of the linear measure sensor, wipe them

off with a cotton swab soaked in absolute

ethanol.

Nozzle U/D Linear Guides (NL Axes)

(2 places)

Every Month Cleaning and Lubrication

(DAPHNE EPONEX GREASE No. 1)

Required Time: 5 minutes

(1) Wipe off the old grease with a rag and

apply a small amount of new grease

with a syringe.

(2) To smooth out the grease, move the

NL axis up and down by 10 mm

through a manual alignment operation

(inching operation).

(3) Wipe off excess grease.

Take ample care not to leave

any waste threads after

cleaning.

Use No. 18 (green) nozzle.

No.18

Note

Notice

Diffusion Plate

Every Month Cleaning

Required Time: 2 minutes

(1) Store all nozzles in the nozzle stocker

(housing) through window navigations.

(2) Wipe the diffusion p late with a dry

lens cleaning cloth.

Sebum or oil should not

adhere to the surface of the

diffusion plate.

Refer to "6. "Nozzle Change"

Window" in "Chapter 3 (Vol. 2)"

for the procedure of nozzle storage.

Nozzle U/D Ball Screw (NL Axis)

Every 3 Months Cleaning and Lubrication

(DAPHNE EPONEX GREASE No. 1)

Required Time: 5 minutes

Wipe off the old grease with a rag and

apply a small amount of new grease to the

groove of the ball screw with a syringe.

Use No. 19 (brown) nozzle.

Note

No. 19

Reference

Coupling

Fig. 4A20