OM-1743-005w.pdf - 第24页
Contents Cont-6 Page OM-1743 1209-001
Contents
Cont-5
Page
OM-1743
1209-001
8. Specications of Tape Feeders ...................................................... 8-1
8.1 Specications of 8 mm Dual Tape Feeder .............................. 8-1
8.1.1 Referential Dimension for Taping (8 mm Paper) ........... 8-2
8.1.2 Referential Dimension for Taping (8 mm Embossed) .... 8-4
9. Reference Taping Specications .................................................... 9-1
9.1 Allowable Limit of Edge Waving of Tape ................................. 9-1
9.2 Test Method for Edge Waving of Tape .................................... 9-1
9.3 Leader Section (Tape End Section) ........................................ 9-2
9.4 Trailer Section (Tape Trailer Section) ...................................... 9-2
9.5 Position of Taped Component ................................................. 9-2
9.6 Strength of Carrier and Cover Tapes ...................................... 9-3
9.7 Peel Strength of Cover Tape ................................................... 9-3
9.8 Minimum Bending Radius ....................................................... 9-3
9.9 Style and Dimensions of Reel ................................................. 9-4
10. Electrical Circuit Diagrams ............................................................. 10-1
10.1 Feeder Control Circuit Diagram
(GT-38080) ........................... 10-1
10.2 Feeder Control Circuit Diagram (GD-38080) .......................... 10-2
10.3 Feeder Control Circuit Diagram (GD-38083) .......................... 10-3
11. Troubleshooting .............................................................................. 11-1
11.1 Component Pick-up Error ....................................................... 11-1
11.2 Tape Feeder not correctly locked ............................................ 11-3
11.3 Tape Feed not correctly performed ......................................... 11-4
11.4 Cover Tape Take-up Action not performed .............................. 11-6
11.5 Cover Tape cut off ................................................................... 11-8
11.6 Cover Tape Take-up Gear does not rotate .............................. 11-9
11.7 Flow Chart for Identifying the Cause of Pick-up Error ............ 11-10
11.7.1 A Vertical Component Occurs ........................................ 11-10
11.7.2 Condition of No Component Occurs .............................. 11-10
11.7.3 Both Conditions of "No component"
and "Vertical component" Occur .................................... 11-11
Contents
Cont-6
Page
OM-1743
1209-001
1209-001
1. Scope
The tape feeders supply chip (taping) components to the chip mounter for
SIGMA-F8.
1.1 Types of Tape Feeders
•
Tape Feeder
Table A1
Tape Feeder
Tape Width × Feed Pitch
(mm)
Type of
Tapes
Mass
(kg)
Power Supply
Barcode
Label
Color
GT-38080
8 mm Dual
Tape Feeder
8 × 2, 4 Paper
Embossed
Approx.
2.5
DC24V
±
10% White
•
Tape Feeder with The Joint Detection Unit
Table A2
Tape Feeder
Tape Width × Feed Pitch
(mm)
Type of
Tapes
Mass
(kg)
Power Supply
Barcode
Label
Color
GD-38080
8 mm Dual
Tape Feeder
8 × 2, 4 Paper
Embossed
Approx.
2.6
DC24V
±
10%
White
GD-38083
8 mm Dual
Tape Feeder
(0402, 0603,
1005) (Note)
8 × 1, 2 Paper
Embossed
Blue
+
White
Note
(a) GD-38083 is applicable to 1 mm pitch tape.
(b) The barcode label part No. is described with "-" omitted as "GT38080".
1. Scope
OM-1743
1-1