OM-1743-005w.pdf - 第98页
7.3 Maintenance Check List 7.3.1 Daily Maintenance in Each Section T able G2 Location to be Maintained Work Working T ools Check Name Reference Drawing Suppressor Section Upper Surface of Suppressor Fig. G2 Cleaning V ac…
MOLYNOC GREASE AP1 (NIPPON OIL CORPORATION) or its equivalent
Table G1
Grease Names Makers
DAPHNE M-No.1 Idemitsu Kosan Co., Ltd
JOMO Lisonix Grease M No. 1 JX Nippon Oil & Energy
COSMO MOLYBD GREASE No. 1 COSMO OIL LUBRICANTS
BEACON Q2 ESSO OIL
Gemico MD2 TonenGeneral Sekiyu K.K.
M5 GREASE 1 KYGNUS
1209-001
7.2 Preparation for Maintenance
OM-1743
7-3
7.3 Maintenance Check List
7.3.1 Daily Maintenance in Each Section
Table G2
Location to be Maintained
Work Working Tools Check
Name
Reference
Drawing
Suppressor Section Upper Surface
of Suppressor
Fig. G2 Cleaning Vacuum Cleaner, Rag, Toothbrush
7.3.2 Weekly Maintenance
Table G3
Location to be Maintained
Work Working Tools Check
Name
Reference
Drawing
Suppressor Section Chute Fig. G3 Cleaning Rag, Alcohol
Suppressor
(Rear Side)
Fig. G4 Cleaning Rag or Cotton Swab, Alcohol
Peeling Section Fig. G5 Cleaning Cotton Swab or Toothbrush
Cover Tape Take-up
Section
Tape Guide
Roller
Fig. G7 Cleaning Rag, Alcohol
Component
Discharging Section
Discharging
Outlet
Fig. G8 Cleaning Air Gun
Splicing Detection
Unit Section
Tage Guide Fig. G9 Cleaning Cotton Swab, Alcohol
Bamboo Probe (Line Accessory)
7.3.3 Quarterly Maintenance
Table G4
Location to be Maintained
Work Working Tools Check
Name
Reference
Drawing
Tape Feed Gear
Section
*
Worm Gear Fig. G10 Cleaning,
Lubrication
Rag, Bamboo Probe (Line
Accessory), Greasing Jig,
MOLYNOC GREASE AP1
Cover Tape Take-up
Gear Section
*
Flat End
Wheel,
Worm Gear
Fig. G11 Cleaning,
Lubrication
Rag, Bamboo Probe (Line
Accessory), Greasing Jig,
MOLYNOC GREASE AP1
Suppressor Section Pick-up
Position
Fig. G6 Check,
Adjustment
Feeder Adjusting Jig JG-0209
(Purchase separately)
Note
* Perform the maintenance after rst every 5 million times of operation or
every 3 months whichever comes rst.
1209-001
7.3 Maintenance Check List
OM-1743
7-4
7.4 Maintenance Spots
7.4.1 Description of Maintenance in Each Section
Here the maintenance cycle for each section of the tape feeder.
GT-38080 is given as the example in the description of the procedure.
This procedure applies to almost all the tape feeders, except for those with special
descriptions.
How to Locate the Check, Cleaning, Lubrication and Adjustment Spots
Chute
Every week Cleaning
Lift the suppressor and clean it with a rag
soaked in alcohol.
(a) When the chute is cleaned,
remove the Magnetic Plate.
If the tape is set with any foreign
substance attached, it might
cause a suppressor deformation
or pick-up error.
[1]
[2]
[3]
Notice
(b)
Fig. G1
[1]
: Maintenance Spot
[2]
: Maintenance Cycle and Contents
[3]
: Details of Maintenance
1209-001
7.4 Maintenance Spots
OM-1743
7-5