OM-1743-005w.pdf - 第88页

1209-001 6.5 8 mm Width T ape Splicing Procedure 6.5.1 Cutting New T ape CAUTION Cut it off with the greatest care so as not to cut your nger . (1) Prepare a new tape. Peel off the cover tape up to the splicing position…

Notice

(a) When splicing, do so when the remaining tape level reaches less

than the "0.2" position marked on the side surface of the reel.

0.8

0.6

0.4

0.2

Fig. F9

(b) Before using the tape cutting jig, make sure that there is no dust or

debris on the cutter blades.

If there is any debris or dust on the cutter blades, remove it by

blowing air or with a cotton swab.

If there is any debris or dust on the cutter blades, such debris or dust

may attach to the tape and the adhesive force of the splicing tape

may be reduced.

The adhesive force might be reduced.

(d) When you have touched the adhesive side of the splicing tape or the

splicing tape is re-used after it has been peeled off, do not use that

tape. Splice it with a new tape.

(e) When the splicing tape is to be peeled off from the peeling paper, do

so after the tape cut processing.

(f) Always fold the splicing tape along the perforations.

Doing otherwise may cause the splicing tape to swell out from the

tape edge and so lead to tape feeding error of the tape feeder.

(g) Do not use the tape cutting jig except for the splicing operation.

Do not use the tape cutting jig to cut any chip component.

Doing otherwise may cause a chip on a blade or deformation of the

pilot pin, which would result in inaccuracy of tape splicing caused by

a tape cutting error and so cause tape feed error in the tape feeder.

(h) After splicing, take out the cover tape from the cover tape storage

section in the tape feeder.

Note

For the tape where the releasing treatment has been done on the cover tape

surface, the adhesive force might be weak and the tape be peeled off easily.

1209-001

6.4 Splicing Operation

OM-1743

6-7

1209-001

6.5 8 mm Width Tape Splicing Procedure

6.5.1 Cutting New Tape

CAUTION

Cut it off with the greatest care so as not to cut your nger.

(1) Prepare a new tape.

Peel off the cover tape up to the

splicing position.

(2) Cut the tape, using the tape cutting

jig.

Attach the tapes onto the tape cut

jig and cut the tapes with cover tape

and carrier tape overlapped.

•

Take care not to cut any component

in order to prevent damage to the

tape cutting jig.

There should be no component here.

Mirror Surface

(Make sure that there is no component in

the component compartment hole on the

rear side of the carrier tape).

Pilot Pins

Scissors

Cover Tape

(3) The preparation of new tape has

been completed.

Make sure that the end of the cover

tape is peeled off a little from the

carrier tape.

Cover Tape

Carrier Tape

Splicing Position

(Cut Position)

Component Compartment

Hole

Pilot Pins

Cut the tape at the Component Compartment Hole.

6.5 8 mm Width Tape Splicing Procedure

OM-1743

6-8

1209-001

6.5.2 Cutting Tape on Feeder Side

(1) Prepare the tape on the feeder side.

(2) Cut the tape on the feeder side.

Set the tape on the pilot pins and cut

it.

•

Take care not to cut any component

in order to prevent damage to the

tape cutting jig.

(3) The preparation of the tape on the

feeder side has been completed.

If it tends to bend, correct it.

Feeder Side

Section where the

components are

not included

Section where

the components are included

Cut Position

6.5 8 mm Width Tape Splicing Procedure

OM-1743

6-9