西门子SIPLACE S-27 HM用户手册.pdf - 第105页
User Manual SIPLAC E S-27 HM 4 Setting up the placement machine Software vers ion SR.503.xx 07/ 2003 US Edition 4.1 Transport dimensions 105 4 Setting up the placement machine 4.1 T ransport dime nsions 4 Fig. 4.1 - 1 Di…
3 Technical data User Manual SIPLACE S-27 HM
3.10 PCB conveyor Software version SR.503.xx07/2003 US Edition
104
3.10.3.2 Technical data – dual conveyor
3
Fixed conveyor side Right (standard), left (optional)
Maximum component height
6 mm for the 12-segment Collect&Place head
8.5 mm for the 6-segment Collect&Place head
PCB format 50 mm x 50 mm to 508 mm x 216 mm
2" x 2" to 20" x 8.5"
Long board: up to 610 mm (24"), (option)
PCB thickness 0.5 mm to 4.5 mm
Max. PCB warpage Up: 4.5 mm - PCB thickness
On bottom: 0.3 mm + PCB thickness
Clearance on PCB underside Standard: 25 mm
Option: max. 40 mm
PCB transport height 830 mm ± 15 mm (standard)
900 mm ± 15 mm (optional)
930 mm ± 15 mm (optional)
950 mm ± 15 mm (SMEMA: optional)
Type of interface Siemens (standard), (SMEMA optional)
Component-free PCB handling edge 3 mm
PCB changeover time 2.5 s
Conveyor mode Synchronous or asynchronous
Components on each conveyor Synchronous: different, asynchronous: same
PCB width on each conveyor Same
Ink spot recognition Synchronous: not possible, asynchronous: possible
Automatic width adjustment Synchronous: not possible, asynchronous: possible
User Manual SIPLACE S-27 HM 4 Setting up the placement machine
Software version SR.503.xx 07/2003 US Edition 4.1 Transport dimensions
105
4 Setting up the placement machine
4.1 Transport dimensions
4
Fig. 4.1 - 1 Dimensions of the placement machine during transportation and setting up
4
(A) Points for attaching the fork-lift truck (fork length 1600 mm)
(1) Input conveyor
(2) Output conveyor
4
The standard PCB conveyor height is 830 mm 15 mm. The standard overall height of the
machine is 1980 mm. For a PCB conveyor height of 950 mm (SMEMA option), this gives an
overall height of 2100 mm.
4 Setting up the placement machine User Manual SIPLACE S-27 HM
4.1 Transport dimensions Software version SR.503.xx07/2003 US Edition
106
4.1.1 Transport configuration and transportation
The following components are not installed when the placement machine is delivered from the
factory:
– Keyboards
–Monitors
– Fault indicator lamp and
– Component trolley
Æ Install the dismantled components for commissioning.
Æ Use a fork-lift truck to transport the placement machine with a minimum fork length of
1600 mm.
Æ Attach the fork-lift truck only at the indicated points.
4.1.2 Quality of the foundation
Æ Ensure that
– you set up the placement machine on a firm and non-vibrating foundation.
– the load bearing capacity per unit area of the foundation is greater than 1000 kg/m².
4.1.3 Compressed air supply
– The pressure of the compressed air supply must be 0.55 MPa (5.5 bar) min. The maximum
permitted value is 0.8 MPa (8 bar).
– The compressed air must conform to the specification (see Section 3.4
from page 80).
This can be achieved with
– oil-free compressors, e.g. Atlas, Copco type ZR4
– compressed air washer/driers
– micro-filters, series X, e.g. from Zander
4.1.4 Main power supply
– The power socket must be fused. The fuse ratings are:
3 x 16 A for 3 x 400 VAC / 3 x 208 VAC/3 x 200 VAC 4