AltaPail II Bulk Melters Product Manual.pdf - 第20页

Safety 1-9 E 11/2014 Nordson Corporation Safe_PPA1011LUE_EN Table 1-1 Genera l Safet y Warnings and Cautio ns (contd) Equipment Type Warning or Caution HM, CA, PC WARNING! Allow only pe rsonnel with appropriate tra ining…

100%1 / 230
Safety
1-8
E 11/2014 Nordson Corporation
Safe_PPA1011LUE_EN
General Safety Warnings and Cautions
(contd.)
Table 1-1 General Safety Warnings and Cautions (contd)
Equipment
Type
Warning or Caution
HM
WARNING! Molten material! Wear eye or face protection, clothing that
protects exposed skin, and heat-protective gloves when servicing
equipment that contains molten hot melt. Even when solidified, hot melt
can still cause burns. Failure to wear appropriate personal protective
equipment can result in personal injury.
HM, PC
WARNING! Equipment starts automatically! Remote triggering devices
are used to control automatic hot melt applicators. Before working on
or near an operating applicator, disable the applicator's triggering
device and remove the air supply to the applicator's solenoid valve(s).
Failure to disable the applicator's triggering device and remove the
supply of air to the solenoid valve(s) can result in personal injury.
HM, CA, PC
WARNING! Risk of electrocution! Even when switched off and
electrically isolated at the disconnect switch or circuit breaker, the
equipment may still be connected to energized auxiliary devices.
De-energize and electrically isolate all auxiliary devices before
servicing the equipment. Failure to properly isolate electrical power to
auxiliary equipment before servicing the equipment can result in
personal injury, including death.
HM, CA, PC
WARNING! Risk of fire or explosion! Nordson adhesive equipment is
not rated for use in explosive environments and has not been cerfified
for the ATEX directive or as nonincendive. In addition, this equipment
should not be used with solvent-based adhesives that can create an
explosive atmosphere when processed. Refer to the MSDS for the
adhesive to determine its processing characteristics and limitations.
The use of incompatible solvent-based adhesives or the improper
processing of solvent-based adhesives can result in personal injury,
including death.
Continued...
Safety
1-9
E 11/2014 Nordson Corporation
Safe_PPA1011LUE_EN
Table 1-1 General Safety Warnings and Cautions (contd)
Equipment
Type
Warning or Caution
HM, CA, PC
WARNING! Allow only personnel with appropriate training and
experience to operate or service the equipment. The use of untrained
or inexperienced personnel to operate or service the equipment can
result in injury, including death, to themselves and others and can
damage to the equipment.
HM
CAUTION! Hot surfaces! Avoid contact with the hot metal surfaces of
applicators, hoses, and certain components of the melter. If contact
can not be avoided, wear heat-protective gloves and clothing when
working around heated equipment. Failure to avoid contact with hot
metal surfaces can result in personal injury.
HM
CAUTION! Some Nordson melters are specifically designed to
process polyurethane reactive (PUR) hot melt. Attempting to process
PUR in equipment not specifically designed for this purpose can
damage the equipment and cause premature reaction of the hot melt. If
you are unsure of the equipment's ability to process PUR, contact your
Nordson representative for assistance.
HM, CA
CAUTION! Before using any cleaning or flushing compound on or in
the equipment, read and comply with the manufacturer's instructions
and the MSDS supplied with the compound. Some cleaning
compounds can react unpredictably with hot melt or cold adhesive,
resulting in damage to the equipment.
HM
CAUTION! Nordson hot melt equipment is factory tested with Nordson
Type R fluid that contains polyester adipate plasticizer. Certain hot melt
materials can react with Type R fluid and form a solid gum that can
clog the equipment. Before using the equipment, confirm that the hot
melt is compatible with Type R fluid.
Safety
1-10
E 11/2014 Nordson Corporation
Safe_PPA1011LUE_EN
Other Safety Precautions
S
Do not use an open flame to heat hot melt system components.
S
Check high pressure hoses daily for signs of excessive wear, damage, or
leaks.
S
Never point a dispensing handgun at yourself or others.
S
Suspend dispensing handguns by their proper suspension point.
First Aid
If molten hot melt comes in contact with your skin:
1. Do NOT attempt to remove the molten hot melt from your skin.
2. Immediately soak the affected area in clean, cold water until the hot melt
has cooled.
3. Do NOT attempt to remove the solidified hot melt from your skin.
4. In case of severe burns, treat for shock.
5. Seek expert medical attention immediately. Give the MSDS for the hot
melt to the medical personnel providing treatment.