00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第251页

7 Conveyor 7.6 Conveyor Belt, Belt Drive and Hexagonal Shaft Service Manual SIPLACE X-Serie S 06/2019 251 7.6.5 Replacing the idler pulley Parts, equipment and tools ● Idler pulley SXa [03092899Sxx] (including screws, sp…

100%1 / 428
7 Conveyor
7.6 Conveyor Belt, Belt Drive and Hexagonal Shaft
250 Service Manual SIPLACE X-Serie S 06/2019
7.6.3 Replacing the tape drive
Parts, equipment and tools
●
Belt drive assembly SXa [03092315-xx]
●
Bearing for hexagonal shaft SXa (plastic bearing) – pack of 10 [03092024-xx]
Overview
Fig.319: Overview of tape drive
1. Tape drive
2. Washer under the top fastening screw
Removal and installation
► Replacement of the belt drive is identical to replacement of the conveyor drive. For more in-
formation about this read section 7.4.1 "Replacing the conveyor drive" [}218].
7.6.4 Replacing the drive shaft on the tape drive
Parts, equipment and tools
●
Synchronous shaft assembly SXa [03092383-xx]
●
Bearing for hexagonal shaft SXa (plastic bearing) – pack of 10 [03092024-xx]
Removal and installation
► Replacement of the drive shaft on the tape drive is follows the same procedure as replace-
ment of the toothed belt on the conveyor drive.
7.4.4 "Replacing the toothed belt (conveyor drive)" [}223]
7 Conveyor
7.6 Conveyor Belt, Belt Drive and Hexagonal Shaft
Service Manual SIPLACE X-Serie S 06/2019 251
7.6.5 Replacing the idler pulley
Parts, equipment and tools
●
Idler pulley SXa [03092899Sxx] (including screws, spacer and clamping device)
●
Magnet lifter, if needed or tweezers and adhesive tape
●
Torx screwdriver ESD 1.0-5.0 Nm [03078400-xx]
●
Bit holder for TorqueVario screwdriver [03078706-xx]
●
Bit, size 4
●
Measuring scale, if needed
Overview
Fig.320: Overview of idler pulley
1. Idler pulley
2. Fastening screw for idler pulley
 WARNING!
Tighten the fastening screw with a
torque of 1.8 Nm. Make sure that you
do not tighten the screws too much.
This could cause irreparable damage
to the conveyor!
The corresponding thread is only in 1.5
to 2 mm thick plates and could be
damaged if you use a torque which is
too high.
For this reason, avoid using screws
which are too short. Use a measuring
scale to check, if needed!
This could cause irreparable damage
to the conveyor!
.
Installation location of idler pulley Fastening screw
Placement area ISO10642 - M4x6
Movable idler pulleys ISO10642 - M4x8
Other positions in the input, intermediate and output area ISO10642 - M4x10
Exception: conveyor side A next to the LLS transmitter ISO10642 - M4x8
First and last idler pulley on the transfer positions to the prede-
cessor and successor machine
One additional spacer disk
7 Conveyor
7.6 Conveyor Belt, Belt Drive and Hexagonal Shaft
252 Service Manual SIPLACE X-Serie S 06/2019
Removal
CAUTION
Toothed belt
► Make sure that the toothed belt is not folded or otherwise damaged.
► Use the software to move the conveyor sides into a position which allows you best access. As
an alternative, you can loosen the clamps for the relevant sides in dual conveyors.
7.2 "Loosening the Conveyor Side Clamps" [}207]
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Loosen the movable idler pulley.
NOTICE
Replacing a movable idler pulley
The idlers are fitted onto a clamping device [00360422-xx]. When you fit the new movable
idler pulley, this clamping device needs to be pushed towards the movable idler pulley. You
therefore need to perform the following additional steps when replacing a movable idler pul-
ley:
► Dismantle the clamping or guide rail via the movable idler pulley.
Secure the claming piece in the conveyor side with adhesive tape. The lack of room
makes subsequent insertion and fixture highly complicated.
► Remove the fastening screw on the idler pulley to be replaced.
CAUTION
Spacer, spacer disk
The fastening screw for some idler pulleys also holds the spacers or spacer disks in place.
► Make sure that you do not lose these.
► Unthread the idler pulley from the conveyor toothed belt and remove it.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following
instructions:
●
Make sure you use the correct fastening screw.
Tighten this fastening screw with a torque of 1.8Nm. Make sure that you do not tighten the
screws too much. This could cause irreparable damage to the conveyor!
●
Use any spacer disks or spacers available.
●
Make sure that you do not fold or otherwise damage the toothed belt.
●
Make sure that the toothed belt is positioned accurately in the guidance on the motor shaft/in
the belt drive.
●
Remove the adhesive tape, if necessary.
●
While you tighten the movable idler pulley, set the tension of the toothed belt correctly
7.6.2 "Setting the belt tension (conveyor belt)" [}247]