00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第308页

8 Head exchange 8.1 Fast Hardware Exchange 308 Service Manual SIPLACE X-Serie S 06/2019 ► Follow the instructions on the screen for all further steps. NOTICE Nozzles In the event of repairs, it is not always possible to …

8 Head exchange

8.1 Fast Hardware Exchange

Service Manual SIPLACE X-Serie S 06/2019 307

8.1.2 Removing and Installing the Placement Head

► For actually removing and installing the placement head hardware, proceed as described in

the relevant chapter.

8.3 "Replacing the SIPLACE C&P20/A/M" [}310]

8.5 "Replacing the SIPLACE C&P20P/M2" [}313]

8.6 "Replacing the SIPLACE CPP/M" [}316]

8.1.3 Completing the FHE in the Software

► Switch the machine on.

After being switched on again the machine issues the message Changed heads detected and ex-

pects a calibration.

Fig.392: Select operator level

► Select the

button, to open the

Configure, update and calibrate the

machine menu.

► Select the

button to open the

Check and set user settings menu.

► Switch over to the operator level Ma-

chine service.

ð The

button will be shown.

Fig.393: Service menu

► Select the Service

button.

► Select the Fast hardware exchange

button.

8 Head exchange

8.1 Fast Hardware Exchange

308 Service Manual SIPLACE X-Serie S 06/2019

► Follow the instructions on the screen for all further steps.

NOTICE

Nozzles

In the event of repairs, it is not always possible to simply return the nozzles from a defective

head to the nozzle changer in order to achieve a defined state. It may not be possible at all

to achieve a defined state. After the head exchange the software stores the nozzle config-

uration of the defective head and the nozzle changer. You can then refill the garages to re-

store the same level as before the head failure.

If the newly fitted head is equipped with calibration nozzles, these will either be placed in

empty nozzle garages or rejected after the calibration. The nozzles required for the job can

then be picked up and the production can be started.

You can also skip refilling the garages. In this case you have to refill the nozzle changer be-

fore the start of the production.

NOTICE

Not enough calibration tools

► If there is no calibration tool present for each head, click on the Cannot supply all

calibration tools at once button. Depending on your machine type you may be

prompted to provide the calibration tool for each head individually.

► If there is an empty magazine in the machine after the calibration has been completed, select

the Remove calibration nozzlesbutton.

► Select the Finish button.

► If there are any problems during the reference run (vacuum check), perform zero correction

for the pressure control valve.

The exchange has now been completed and production can be restarted.

8 Head exchange

8.2 Differentiation of the SIPLACE C&P20 head variants

Service Manual SIPLACE X-Serie S 06/2019 309

8.2 Differentiation of the SIPLACE C&P20 head variants

CAUTION

Do not confuse the different SIPLACE C&P20 head variants.

► Parts from the SIPLACE C&P20/A/M head can not usually be used for the SIPLACE

C&P20P/M2 head (and vice versa)!

Fig.394: Differentiation of the SIPLACE C&P20 head variants

The SIPLACE C&P20/A/M and the SIPLACE C&P20 P/M2 head differ in many details. They are

easily identified by the following features:

1. The SIPLACE C&P20 P/M2 head can be identified by the fan. This fan is not present on the

SIPLACE C&P20/A/M.

2. The component sensor is flatter and wider on the SIPLACE C&P20 P/M2 than on the

SIPLACE C&P20/A/M.