00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第299页

7 Conveyor 7.10 Conveyor sides Service Manual SIPLACE X-Serie S 06/2019 299 Setting ► Use the software to move the conveyor sides into a position which allows you best access. As an alternative, you can loosen the clamps…

7 Conveyor

7.10 Conveyor sides

298 Service Manual SIPLACE X-Serie S 06/2019

7.10.2 Setting the Parallelism of the Conveyor Sides and Adjustment Units

7.10.2.1 Setting the Parallelism of the Adjustment Unit

Setting

► This setting is identical for the dual conveyor. For more information about this, read section

7.10.2.2 "Setting the parallelism of the conveyor side walls and adjustment units for dual con-

veyors" [}298].

NOTICE

Procedure identical to that for adjustment units on dual conveyor

In a single conveyor, the movable conveyor side is directly connected with the recirculating

ball screws of the width adjustment. This is set via the toothed belt. This must jump one or

more teeth via the relevant idler pulleys.

7.10.2.2 Setting the parallelism of the conveyor side walls and adjustment units for dual

conveyors

NOTICE

Adjustment units

The parallelism of the conveyor sides depends on the parallelism of the adjustment units.

This is set via the toothed belt. This must jump one or more teeth via the relevant idler pul-

leys.

► If you unable to set the parallelism, contact your local SIPLACE Service team.

Parts, equipment and tools

Fig.376: Metal pieces

●

To check the adjustment unit stoppers,

you need two suitably sized and

identical pieces of metal (see below).

You could also use two lifting table

plate guides if needed.

Overview

Fig.377: Overview width adjustment

1. Adjustment units

2. Width adjustment drive

3. Movable idler pulley

4. Toothed belt of width adjustment

5. Measurement point for belt tension

6. Idler pulley

7 Conveyor

7.10 Conveyor sides

Service Manual SIPLACE X-Serie S 06/2019 299

Setting

► Use the software to move the conveyor sides into a position which allows you best access. As

an alternative, you can loosen the clamps for the relevant sides in dual conveyors.

7.2 "Loosening the Conveyor Side Clamps" [}207]

► Switch off the machine, disconnect it from the power supply and secure it to prevent

unauthorized reactivation.

1.2 "Preparatory work..." [}16]

► Dismantle the lifting table plate at location 3 and 4.

7.3.1 "Replacing the lifting table plate" [}212]

► Loosen the movable idler pulley for the toothed belt (width adjustment). The toothed belt of

the width adjustment should then have enough play so that you can move the adjustment

units independently of one another. You may need to remove the toothed belt from the idler

pulleys.

Fig.378: Adjustment unit (example of SX1/SX2 shown)

1. Adjustment unit

2. Spacer piece (here:lifting table fixture)

3. Frame

4. Toothed belt of width adjustment

► Place the toothed belt over the two up-

per idler pulleys so that the adjustment

units move exactly parallel to one an-

other. Check the parallelism as follows:

► Push the adjustment units by hand out-

wards, to one side of the conveyor. In-

sert a spacer piece in each case. This

helps you to check the distance to the

frame more easily. Make sure that the

lifting table plate guides are only lying

against the adjustment unit base struc-

tures and not against the threads.

7 Conveyor

7.10 Conveyor sides

300 Service Manual SIPLACE X-Serie S 06/2019

Fig.379: Spacer (example of SX1/SX2 shown)

1 View from the side 2 View from above

3 Spacer piece (here: metal platelet) 4 Adjustment unit

5 Frame 6 Warehouse

► Position the adjustment units so that these lie flush against the lifting table guides between the

frame and the adjustment unit.

► Tighten the fastening screw of the movable idler pulley.

► Check the parallelism of the adjustment units again and correct again if necessary.

► If the conveyor side clamps have loosened, fix these again.

► Set the tension of the toothed belt.

7.5.2.1 "Setting the belt tension (width adjustment)" [}228]

► Calibrate the width adjustment motor.

(The calibration is identical for the lifting table motor.)

► Use the software to move the fixed conveyor side. This ensures that the fixed conveyor side is

parallel to the flexible sides. Readjust the fixed conveyor side to its original value after that.