00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第320页
8 Head exchange 8.7 Replacing the SIPLACE Twin 320 Service Manual SIPLACE X-Serie S 06/2019 Conversion to another installation height Fig.411: Conversion 1. Hole for the fastening screw of the bushing in "head at b…
8 Head exchange
8.6 Replacing the SIPLACE CPP/M
Service Manual SIPLACE X-Serie S 06/2019 319
8.6.1 Preparing the SIPLACE CPP for the installation height
CAUTION
Different heights
The placement head can be installed at two different heights. CPP_L corresponds to a
component height of sixmm. CPP_H corresponds to a component height of 11.5mm.
If the SIPLACE CPP is used in a placement area with stationary camera, SIPLACE Twin or
SIPLACE WPC, it may only be used in the upper position!
Overview
Fig.409: Fastening screws
1. Fastening screws on the left side
2. Fastening screws on the right side
This diagram shows the fastening screws in
the "head at top" position.
Fig.410: SIPLACE CPP – positions
1. Retaining plate
2. "Head at bottom" position
3. "Head at top" position
4. Fixture holes with bushings
8 Head exchange
8.7 Replacing the SIPLACE Twin
320 Service Manual SIPLACE X-Serie S 06/2019
Conversion to another installation height
Fig.411: Conversion
1. Hole for the fastening screw of the
bushing in "head at bottom" position
2. Hole for the fastening screw of the
bushing in "head at top" position
3. Bushing
All four bushings and the retaining plate
must either be fixed in top or bottom posi-
tion.
Proceed as follows when replacing the
bushings:
► Undo the fastening screws of the bush-
ings.
► Insert the bushings in the correct posi-
tion and re-tighten them.
► Perform these steps for all four fasten-
ing bushings and the retaining plate for
the head.
8.7 Replacing the SIPLACE Twin
Parts, equipment and tools
●
Select the relevant placement head:
– Twin Pick&Place module [03033628-xx]
– Twin Pick&Place module THK R2 [03097485-xx]
●
Torque screwdriver 1-5 Nm [03078400-xx]
●
Extension/straight TX20 [03073256-xx]
●
Extension/straight [03043440-xx]
●
Bit holder for Torque Vario-S screwdriver [03078706-xx]
●
Calibration tool version 3 [03010565-xx]
●
For additional work on the placement head:
Head assembly stand [03056231‑xx]
Service manual "Twin/VHF" [DE: 00197468-xx]. [EN: 00197469-xx]
Job Card "Preventive Maintenance Twin" [DE:00197604‑xx] [EN:00197603‑xx] (other lan-
guages available)
Overview
The Twin consists of two identical Twin segments, which are fitted at an angle of 180°.
NOTICE
Module 1 and 2
The removal procedure is described here for module1 (left). Removal for module 2 (right)
is the same.
► In the case of older Twins, module 1 might need to be removed before you can
remove module 2. When fitting them again, you would then need to fit module 2 first,
before module 1.
► In the case of newer Twin heads, the modules can be removed and fitted individually.
8 Head exchange
8.7 Replacing the SIPLACE Twin
Service Manual SIPLACE X-Serie S 06/2019 321
Fig.412: Undetachable screws
NOTICE!
When using modules with Undetach-
able screws(1) you may need to fit
these screws on the other side de-
pending on the installation position.
.
Observe the various different hose lengths:
Designation Item no. Length
Other hoses on the machine:
Hose supplied "Silicon hose Di8 Da12 electrically conductive
1m“
03006727Sxx
●
Cooling air hose X motor
03006777-xx 180 mm
●
Cooling air hose P+P module right
03006779-xx 395 mm
●
Cooling air hose P+P module left
03006780-xx 230 mm
●
Cooling air hose X motor TX
03126503-xx 210 mm
●
Cooling air hose X motor rotated gantry
03059420-xx 440 mm
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Switch off the compressed air supply
5.2 "Disabling the compressed air supply" [}134]
Fig.413: Connectors
► Move the gantry into a position which
allows you best access.
► Unplug the pneumatic connection from
the Twin vacuum generator to the
pneumatic distributor(1) and from the
silencer.
► Disconnect the exhaust air silicone
hose from the Twin vacuum generator
(4).
► Unplug the pneumatic connection from
the pneumatic distributor(1) to the
Twin return cylinder.
► Unplug the flat ribbon cable(2) from
the head main board(3) on the Twin.