00197042-04_SM_X-Serie-S_Customer_EN.pdf - 第353页
9 Component feeding 9.1 Cutter Service Manual SIPLACE X-Serie S 06/2019 353 9.1.14 Replacing the solenoid valves Parts Fig.471: Solenoid valve 03000630-xx Solenoid valve Equipment and tools 00353832-xx Allen key set Wir…
9 Component feeding
9.1 Cutter
352 Service Manual SIPLACE X-Serie S 06/2019
Fig.469: Removing the throttle valve
► Disconnect the air tube(1) from the
throttle valve(2).
► Turn the throttle valve in the direction
"-" and count the turns. Note the num-
ber.
► Remove the throttle valve by using a
SW17 spanner(3).
Installation
► Fit the new throttle valve. Take care of the silicon sealing.
► Close the throttle valve completely in direction "-" and open it again in direction “+” by counting
the noted turnings.
This will ensure a working pre-adjustment for starting the final setting later on.
► Connect the air tube.
► Follow the removal instructions in reverse order for further installation.
► Set the new throttle valve (see below).
9.1.13.1 Times for Setting the Throttle on the Cutter (From SW707.1)
Fig.470: Measuring times
► Switch over to Check sensors and
functions
.
► Select the
button.
► Select Location.
► Select the
button.
► Select Cut to start test.
You have to select the Cut button at
least two times (one for each side).
Repeat if necessary.
► Check the measured times.
NOTICE!
The permitted measurement ranges
will be provided by the software.
.
Cutter Time
Moving the blade out 175 to 200 ms
Moving the blade in 200 to 250 ms
► If necessary: Change the time by adjusting the throttle valves at the short-stroke cylinders.
9 Component feeding
9.1 Cutter
Service Manual SIPLACE X-Serie S 06/2019 353
9.1.14 Replacing the solenoid valves
Parts
Fig.471: Solenoid valve
03000630-xx Solenoid valve
Equipment and tools
00353832-xx Allen key set
Wire cutters
Cable ties
Overview
Fig.472: Cutter
1. Position of the solenoid valves
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Switch off the compressed air supply
5.2 "Disabling the compressed air supply" [}134]
► Loosen the compressed air connections on the solenoid valve.
► Unplug the press-fit connection on the solenoid valve connection cable. Mark the position to
make clear assignment easier later on.
► Remove the screws holding the solenoid valve in place and remove the solenoid valve.
Installation
► Mount the new solenoid valve and reestablish the press-fit connection to the valve.
► Plug in the compressed air connections.
► Attach cables ties if necessary (strain relief).
9 Component feeding
9.1 Cutter
354 Service Manual SIPLACE X-Serie S 06/2019
9.1.15 Replacing the silencer
Parts
Fig.473: Silencer version 1 and 2
03122731‑xx Silencer R1/8 40dB (version2)
(replaces version 1 [00317044‑xx])
If a silencer version 1 is replaced with a version 2 silencer, you will also need to use this push-in fit-
ting:
00320172-xx Push-in L-fitting QSL-1/8-6
Equipment and tools
00096290-xx Fork wrench set
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Switch off the compressed air supply
5.2 "Disabling the compressed air supply" [}134]
► Try to perform the exchange on the installed cutter.
If access is too limited, remove the cutter from the machine.
9.1.3 "Replacing the Cutter on the COT Insert [03066690-xx]" [}329]
Fig.474: Silencer on cutter
► Remove the silencer(1) (SW13).